For Your Safety - Würth 0702 445 Serie Originalbetriebsanleitung

EWS 24.book Seite 14 Dienstag, 29. Oktober 2019 10:09 10
GB
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future refer-
ence.
Working safely with this machine is pos-
sible only when the operating and safety
information are read completely and the
instructions contained therein are strictly
followed. In addition, the general safety instruc-
tions in the enclosed booklet must be followed.
Please also observe the relevant national industrial
safety regulations.
Wear safety goggles.
Wear protective goggles, ear protection.
Wear protective gloves.
Safety warnings common for grinding, working
with wire brushes and cut-off grinding
This power tool is to be used as a grinder, wire
brush and cut-off grinder. Observe all safety
warnings, instructions, illustrations and data
supplied with the power tool. Non-observance
of the following instructions can lead to electric
shock, fire and/or serious injury.
Operations such as sanding, polishing are not
recommended to be performed with this power
tool. Operations for which the power tool was not
designed may create a hazard and cause perso-
nal injury.
Do not use accessories which are not specifically
designed and recommended by the tool manu-
facturer. Just because the accessory can be
attached to your power tool, it does not assure
safe operation.
The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can fly apart.
The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
14

For Your Safety

Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted
by flanges, the arbour hole of the accessory must
fit the locating diameter of the flange. Accessories
that do not match the mounting hardware of the
power tool will run out of balance, vibrate exces-
sively and may cause loss of control.
Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pads for
cracks, tear or excess wear, wire brushes for
loose or cracked wires. If the power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After inspect-
ing and installing an accessory, position your-
self and bystanders away from the plane of the
rotating accessory and run the power tool at
maximum no-load speed for one minute. Dam-
aged accessories will normally break apart dur-
ing this test time.
Wear personal protective equipment. Depend-
ing on application, use face shield, safety gog-
gles or safety glasses. As appropriate, wear
dust mask, hearing protectors, gloves and shop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be
capable of stopping flying debris generated by
various operations. The dust mask or respirator
must be capable of filtrating particles generated
by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
Keep bystanders a safe distance away from
work area. Anyone entering the work area must
wear personal protective equipment. Fragments
of the workpiece or of a broken accessory may fly
away and cause injury beyond the immediate
area of operation.
Hold the power tool by insulated gripping sur-
faces only, when performing an operation
where the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory con-
tacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or
snagged and your hand or arm may be pulled
into the spinning accessory.
Never lay the power tool down until the acces-
sory has come to a complete stop. The spinning
accessory may grab the surface and pull the
power tool out of your control.