Seite 1
Vorwort Inhaltsverzeichnis Einführung SIPROTEC 4/5 Aufbau Vorschaltgerät 7XT71 (für Abmessungen und Anschlüsse den Läufererdschluss- schutz mit 1 Hz bis 3 Hz) Montage und Anschluss Inbetriebnahme 7XT7100-0.A00/EE Wartung und Instandsetzung Lagerung und Transport Handbuch Technische Daten Anhang C53000-B1174-C128-8...
Leistungsmerkmale sind nur dann verbindlich, wenn sie bei Vertragsschluss ausdrücklich vereinbart werden. Marken Dokumentversion: C53000-B1174-C128-8.01 SIPROTEC, DIGSI, SIGRA, SIGUARD, SIMEAS SAFIR, SICAM Ausgabestand: 05.2020 und MindSphere sind Marken der Siemens AG. Jede nicht Version des beschriebenen Produkts: 7XT7100-0.A00/EE autorisierte Verwendung ist unzulässig.
(RoHS-Richtlinie 2011/65/EU) sowie elektrische Betriebsmittel zur Verwendung inner- halb bestimmter Spannungsgrenzen (Niederspannungsrichtlinie 2014/35/EU). Diese Konformität ist das Ergebnis einer Bewertung, die durch die Siemens AG gemäß den Richtlinien in Übereinstimmung mit den Fachgrundnormen EN 61000-6-2 und EN 61000-6-4 für die EMV-Richtlinie, der Norm EN 50581 für die RoHS-Richtlinie und der Norm EN 60255-27 für die Niederspannungsrichtlinie durchgeführt worden ist.
Seite 4
Nur elektrotechnisch qualifiziertes Personal darf ein in diesem Dokument beschriebenes Betriebsmittel (Baugruppe, Gerät) in Betrieb setzen und betreiben. Elektrotechnisch qualifiziertes Personal im Sinne der sicherheitstechnischen Hinweise dieses Dokuments sind Personen, die eine fachliche Qualifikation als Elektro- SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 5
Bestimmungsgemäßer Gebrauch Das Betriebsmittel (Gerät, Baugruppe) darf nur für die in den Katalogen und in der technischen Beschreibung vorgesehenen Einsatzfälle und nur in Verbindung mit von Siemens empfohlenen und zugelassenen Fremdge- räten und -komponenten verwendet werden. Der einwandfreie und sichere Betrieb des Produktes setzt Folgendes voraus: •...
Seite 6
SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Eine detaillierte Beschreibung des Messverfahrens in Verbindung mit dem 7UM62 ist im SIPROTEC-Hand- buch 7UM62, Bestellnummer C53000-G1100-C149, enthalten. 7UM85: Eine detaillierte Beschreibung des Messverfahrens in Verbindung mit dem 7UM85 ist im SIPROTEC-Hand- buch 7UM85, Bestellnummer C53000-G5000-C027, enthalten. SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Für die Aufbauvariante des Gerätes gilt die Schutzart IP20. HINWEIS Sie können das Vorschaltgerät 7XT71 je nach Bestellschlüssel, siehe Kapitel A.1 Bestelldaten und Zubehör, im Schalttafelaufbau und im Schalttafel- oder Schrankeinbau verwenden. SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
In jede Schraubklemme können Sie bis zu 2 Ring- oder Gabelkabelschuhe oder bis zu 2 Kupferleiter fest- schrauben. Die Größe der Ring- oder Gabelkabelschuhe und die maximal möglichen Leiterdurchmesser sind im Kapitel 4 Montage und Anschluss aufgeführt. SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 14
2.2 Vorschaltgerät 7XT7100-0BA00 für Schalttafelaufbau HINWEIS Die jeweils 2 LEDs auf der Frontabdeckung und auf der Rückwand des Gerätes haben die gleichen Funkti- onen. Die Abmessungen des Gehäuses sind im Bild 3-1 dargestellt. SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Die jeweils 2 LEDs auf der Frontabdeckung und auf der Rückwand des Gerätes haben die gleichen Funkti- onen. [le_front-view_flush-mounting-device_7XT71, 1, --_--] Bild 2-2 Vorschaltgerät 7XT7100-0EA00 für Schalttafel- oder Schrankeinbau LED RUN LED ERROR Frontabdeckung Optionsschild Gehäuse Typenschild SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 16
In jede Schraubklemme können Sie bis zu 2 Ring- oder Gabelkabelschuhe oder bis zu 2 Kupferleiter fest- schrauben. Die Größe der Ring- oder Gabelkabelschuhe und die maximal möglichen Leiterdurchmesser sind im Kapitel 4 Montage und Anschluss aufgeführt. Die Abmessungen des Gehäuses sind im Bild 3-2 dargestellt. SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Sie können das Vorschaltgerät 7XT71 je nach Bestellschlüssel, siehe Kapitel A.1 Bestelldaten und Zubehör, im Schalttafelaufbau und im Schalttafel- oder Schrankeinbau verwenden. Schraubklemmen der Anschlussleiste Die Schraubklemmen der 18-poligen Anschlussleiste an der Rückwand sind im Lieferzustand lose gedreht. SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 20
Wenn Sie Ring- oder Gabelkabelschuhe mit nicht isolierter Crimp-Zone oder Aderendhülsen mit nicht isolierter Crimp-Zone verwenden, muss die Crimp-Zone zur Einhaltung der Isolationsstrecken mit einem Schrumpfschlauch isoliert sein. Verwenden Sie ausschließlich Kupferleiter! Anschluss an Gerät 2 Anschluss an Gerät 1 SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 21
Abmessungen und Anschlüsse 3.2 Anschlüsse der Vorschaltgeräte 7XT7100 Tabelle 3-2 Anschlussdaten für Kabelschuhe und Leiter Anschluss mit Kabelschuhen Innendurchmesser 4 mm Siemens empfiehlt Kabelschuhe von Tyco Elect- ronics AMP: Außendurchmesser max. 10 mm Ringkabelschuhe: PIDG PN 320565-0 Leiterquerschnitte 1,0 mm...
Seite 22
SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Wenn das Gerät beim Transport beschädigt wurde, dann dürfen Sie es nicht anschließen und in Betrieb nehmen. Beachten Sie weitere in der Verpackung beigelegte Hinweise. ² Heben Sie die Transportverpackung für einen eventuellen Weiterversand auf. ² SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Sie die Winkel an. Die 2 Bohrungen auf der schmalen Seite der Z-Winkel verfügen über M4-Gewinde. [scanbauzink, 1, de_DE] Bild 4-2 Anbau der Z-Winkel an der Frontabdeckung Befestigen Sie das Gerät mit 4 Schrauben an der Schalttafel. ² SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Montage und Anschluss 4.2 Schalttafelaufbau (7XT7100-0BA00) HINWEIS Beachten Sie die Maße und Hinweise im Kapitel 3.1 Abmessungen der Vorschaltgeräte 7XT7100. Bei dieser Montageart ist die Anschlussleiste von vorn zugänglich. ² SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
[le_view_front-device_7XT71, 1, --_--] Bild 4-3 Einbau des Gerätes in die Schalttafel M4-Schrauben Schieben Sie die beiden Abdeckkappen wieder in die Frontabdeckung (siehe Bild 4-1). ² Verdrahten Sie das Gerät gemäß Kapitel Anschluss. ² SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 28
Montage und Anschluss 4.3 Schalttafel- oder Schrankeinbau (7XT7100-0EA00) Bei dieser Montageart ist die Anschlussleiste von hinten zugänglich. SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Beachten Sie die Angaben im Kapitel 3.2 Anschlüsse der Vorschaltgeräte 7XT7100 unter Schraubklemmen der Anschlussleiste. Achten Sie darauf, dass beim Anschließen von 2 Kupferleitern in einer Schraubklemme beide Leiter unlös- baren Kontakt mit der Schraubklemme haben. SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 30
SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
5.1 Allgemeine Hinweise Allgemeine Hinweise HINWEIS Wenn Sie das Gerät erstmalig oder nach längerer Lagerung in Betrieb nehmen, empfiehlt Siemens, es mindestens 2 Stunden im Betriebsraum liegen zu lassen, um einen Temperaturausgleich zu schaffen und um Feuchtigkeit sowie Betauung zu vermeiden.
Lösen und entfernen Sie die jeweils 2 Schrauben am unteren und oberen Z-Winkel, mit denen das Gerät ² an der Schalttafel befestigt ist. Nehmen Sie das Gerät von der Schalttafel ab. ² SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Wenn Sie die erforderlichen Arbeiten an der Flachbaugruppe ausgeführt haben, bauen Sie die Steckbau- ² gruppe sinngemäß in umgekehrter Reihenfolge wieder ein. 5.2.3 Frequenzeinstellung Mit dem DIP-Schalter S1 auf der Flachbaugruppe können Sie die Umpolfrequenz (Frequenz des Rechteckgene- rators) einstellen. SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 35
Wenn Sie die Leiter von der Anschlussleiste getrennt haben, dann schließen Sie die Leiter wieder an den ² Schraubklemmen an. Achten Sie dabei auf die korrekte Verdrahtung. Nehmen Sie das Gerät in Betrieb. ² Kontrollieren Sie am 7UM62/7UM85 die Prüfwerte für das Vorschaltgerät 7XT71. ² SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 36
Bild 5-4 Aufkleber für eingestellte Frequenz HINWEIS Wenn der 7UM62/7UM85 noch keine korrekten Werte anzeigt, wiederholen Sie die Frequenzeinstellung am Vorschaltgerät 7XT71 so oft, bis die Werte annähernd den erforderlichen Betriebsbedingungen entspre- chen. SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Das Vorschaltgerät 7XT71 verfügt über je 2 LEDs auf der Frontabdeckung und auf der Rückwand. Die LEDs mit gleicher Bezeichnung sind parallel geschaltet, sodass je nach Aufbau- oder Einbauvariante des Gerätestatus eingesehen werden kann. Tabelle 5-1 Betriebszustände signalisiert mit LEDs Bedeutung Gerät betriebsbereit ERROR Gerät nicht betriebsbereit SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 38
SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Wartung und Instandsetzung 6.1 Wartung Wartung Das Vorschaltgerät 7XT71 ist wartungsfrei. Wenn erforderlich, wischen Sie das Gerät mit einem sauberen, trockenen und weichen Tuch ab. Benutzen Sie keine Lösungsmittel. SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Auswechseln der Feinsicherung F1 auf der Flachbaugruppe. Im Vorschaltgerät 7XT71 sind spezielle elektronische Bauelemente eingesetzt, die nach den Richtlinien für elektrostatisch gefährdete Bauele- mente (EGB) nur der Hersteller auswechseln darf. Wenn Sie einen Defekt im Gerät vermuten, dann empfiehlt Siemens, das komplette Gerät in das Herstel- ² lerwerk einzusenden.
Seite 42
Wenn Sie die Leiter von der Anschlussleiste getrennt haben, dann schließen Sie die Leiter wieder an den ² Schraubklemmen an. Achten Sie dabei auf die korrekte Verdrahtung. Nehmen Sie das Gerät in Betrieb. ² SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
+35 °C einzuhalten, um einer vorzeitigen Alterung der eingesetzten Elektrolytkondensatoren vorzubeugen. Außerdem empfiehlt Siemens, bei langer Lagerungszeit das Gerät einmal jährlich für 1 bis 2 Tage an die Hilfs- spannung anzuschließen, um die eingesetzten Elektrolytkondensatoren zu formieren. Ebenso sollten Sie vor einem geplanten Einsatz des Gerätes verfahren.
Batterien die lokalen und internationalen Richtlinien. REACH/RoHS-Deklaration Unsere aktuellen REACH/RoHS-Deklarationen sind auf folgender Webseite erhältlich: https://www.siemens.com/global/de/home/produkte/energie/ecotransparency/ecotransparency-down- loads.html HINWEIS Weitere Informationen zu Maßnahmen und Programmen zum Klimaschutz finden Sie auf unserer EcoTransparency-Website: https://www.siemens.com/global/de/home/produkte/energie/ecotransparency.html SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 46
SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
7XP20, 1/6 19"-Gehäuse Abmessungen (H x B x T) 7XT7100-0BA00 312,8 mm x 75,0 mm x 243,5 mm mit Z-Winkeln und Anschlussleiste 7XT7100-0EA00 266,0 mm x 75,0 mm x 235,5 mm mit Anschlussleiste SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 49
Technische Daten 8.1 Allgemeine Gerätedaten Masse 7XT7100-0BA00 2,3 kg 7XT7100-0EA00 2,1 kg Schutzart gemäß EN 60529 Frontseite IP51 Gehäuse und Klemmen IP20 Firmware-Version des Schutzgerätes 7UMxx 7UM85 ≥ V07.30 7UM62 ≥ V04.70 SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
-5 °C bis +40 °C Nennhilfswechselspannung +10 % -5 °C bis +55 °C Grenztemperaturen bei Lagerung -25 °C bis +55 °C bei Transport -25 °C bis +70 °C Lagerung und Transport mit werksmäßiger Verpackung SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 53
Im Jahresmittel ≤ 75 % relative Luftfeuchte; An 56 Tagen im Jahr bis zu 95 % relative Luftfeuchte; Betauung im Betrieb unzulässig! Siemens empfiehlt, die Geräte so anzuordnen, dass sie keiner direkten Sonneneinstrahlung und keinem starken Temperaturwechsel, bei dem Betauung auftreten kann, ausgesetzt sind. Andere Umweltinformationen Maximale Höhe über NN...
Seite 54
SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
[scblochsb, 1, --_--] Bild A-2 Blockschaltbild Vorschaltgerät 7XT71 ACHTUNG Die Spannung zwischen Klemme 1 und Klemme 2 darf AC 300 V nicht überschreiten. Nichtbeachtung kann zu Sachschäden führen. Wenden Sie geeignete Schutzmaßnahmen an. ² SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Wenden Sie geeignete Schutzmaßnahmen an. ² Anschlusspläne mit dem Widerstandsgerät 7XR8004 [dw_7xr8004 connex1, 2, de_DE] Bild A-3 Anschlussbeispiel für die Erregung über Schleifringe [dw_7xr8004 connex2, 2, de_DE] Bild A-4 Anschlussbeispiel für die Erregung über rotierende Gleichrichter SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 59
Anhang A.3 Anschlusspläne Anschlusspläne mit dem Widerstandsgerät 7XR8004 oder 7XR6004 [le_7xr8004_6004, 1, --_--] Bild A-5 Anschlussplan für Erregerspannungen < DC 850 V Anschlussbelegung mit 7XR8004 Anschlussbelegung mit 7XR6004 SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 60
Anhang A.3 Anschlusspläne [le_7xr8004_6004_less_dc, 1, --_--] Bild A-6 Anschlussplan für Erregerspannungen < DC 1200 V Anschlussbelegung mit 7XR8004 Anschlussbelegung mit 7XR6004 SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Überarbeitung der Hardware 7XT7100-0EA00/DD Überarbeitung Gehäuse Neue 18-polige Schraubklemme, Achtung: Anschlüsse haben sich geändert Anschluss von 2 Geräten 7UM62/7UM85 möglich 7XT7100-0BA00/EE Verbesserung der Firmware 7XT7100-0EA00/EE Aktualisierung der Produktinformation mit SIPROTEC 5 7UM85. SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 62
SIPROTEC 4/5, Vorschaltgerät 7XT71, Handbuch C53000-B1174-C128-8, Ausgabe 05.2020...
Seite 63
Preface Table of Contents Introduction SIPROTEC 4/5 Structure Injection unit 7XT71 (for Dimensions and Connections the rotor ground-fault protection with 1 Hz to 3 Assembly and Connection Commissioning Maintenance and Repair 7XT7100-0.A00/EE Storage and Transport Manual Technical Data Appendix C53000-B1174-C128-8...
Document version: C53000-B1174-C128-8.01 Trademarks Edition: 05.2020 SIPROTEC, DIGSI, SIGRA, SIGUARD, SIMEAS SAFIR, SICAM, Version of the product described: 7XT7100-0.A00/EE and MindSphere are trademarks of Siemens. Any unautho- rized use is prohibited.
Seite 65
The product conforms with the international standards of IEC 60255 and the German standard VDE 0435. Standards Additional Support For questions about the system, contact your Siemens sales partner. Customer Support Center Our Customer Support Center provides a 24-hour service. Siemens AG...
Seite 66
Siemens. Problem-free and safe operation of the product depends on the following: • Proper transport • Proper storage, setup and installation • Proper operation and maintenance SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Caution, risk of electric shock Caution, risk of danger, ISO 7000, 0434 Protective Insulation, IEC 60417, 5172, Safety Class II devices Guideline 2002/96/EC for electrical and electronic devices Guideline for the Eurasian Market SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 68
SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 69
Maintenance........................38 Repair..........................39 Storage and Transport..........................41 Description........................42 Environmental Protection Hints..................43 Technical Data............................45 General Device Data......................46 Tests..........................48 8.2.1 Electrical Tests......................48 8.2.2 Mechanical Tests......................50 8.2.3 Climatic Stress......................50 SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 70
Table of Contents Appendix..............................53 Ordering Information and Accessories................54 Block Diagram........................55 Connection Diagrams......................56 Revision History........................ 59 SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 72
SIPROTEC manual 7UM62, order number C53000-G1100-C149. 7UM85: You can find a detailed description of the method of measurement in connection with the 7UM85 in the SIPROTEC manual 7UM85, order number C53000-G5000-C027. SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Structure General Installation Injection Unit 7XT7100-0BA00 for Panel Surface Mounting Injection Unit 7XT7100-0EA00 for Panel Flush Mounting or Cabinet Flush Mounting SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
You can use the injection unit 7XT71 in panel surface mounting and in panel flush mounting or cabinet flush mounting, depending on the order code, see chapter A.1 Ordering Information and Accessories. SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
You can screw up to 2 ring-type or fork-type lugs or up to 2 copper conductors to each screw terminal. The size of the ring-type or fork-type lugs and the maximum possible conductor diameters are listed in chapter 4 Assembly and Connection. SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 76
The 2 LEDs on the front cover and the 2 on the rear plate of the device have the same functions. The dimensions of the housing are shown in Figure 3-1. SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
The 2 LEDs on the front cover and the 2 on the rear plate of the device have the same functions. [le_front-view_flush-mounting-device_7XT71, 1, --_--] Figure 2-2 Injection Unit 7XT7100-0EA00 for Panel Flush Mounting or Cabinet Flush Mounting LED RUN LED ERROR Front cover Option plate Housing Name plate SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 78
4 Assembly and Connection. The dimensions of the housing are shown in Figure 3-2. SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Dimensions and Connections Dimensions of the Injection Units 7XT7100 Connections of the Injection Units 7XT7100 SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Injection Unit 7XT7100-0BA00 for Panel Surface Mounting Injection Unit 7XT7100-0EA00 for Panel Flush Mounting or Cabinet Flush Mounting [scInjUsthouse, 1, en_US] Figure 3-2 Injection Unit 7XT7100-0EA00 for Panel Flush Mounting or Cabinet Flush Mounting SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
A.1 Ordering Information and Accessories. Screw Terminals for the Junction Block In as-delivered condition, the screw terminals of the 18-pin junction block on the rear plate are loosened. SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 82
If you use ring-type or fork-type lugs with a non insulated crimp zone or bootlace ferrules with a non insu- lated crimp zone, the crimp zone must be insulated with heat-shrink tubing to maintain the insulation distance. Only use copper conductors! Connector on device 2 Connector on device 1 SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 83
Stripping length 9 mm to 10 mm that it is drawn in when tightening the screw Tightening torque 1.8 Nm terminal. If you use stranded-wire conductors, you need terminal lugs. SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 84
SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
If the device has been damaged during transport, do not connect and commission it. Comply with any additional notes enclosed with the packaging. ² Keep the transport packaging for any future shipping. ² SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Z-shaped angle brackets have M4 threads. [scanbauzink, 1, en_US] Figure 4-2 Fixing the Z-Shaped Angle Brackets on the Front Cover Fix the device to the panel with 4 screws. ² SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 88
NOTE Pay attention to the dimensions and notes in chapter 3.1 Dimensions of the Injection Units 7XT7100! In this type of assembly, the junction block is accessible from the front. ² SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Push the 2 covering caps back into the front cover (see Figure 4-1). ² Wire the device according to chapter Connection. ² In this type of assembly, the junction block is accessible from the back. SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
3.2 Connections of the Injection Units 7XT7100 under Screw Terminals of the Junction Block. When connecting 2 copper conductors in 1 screw terminal, make sure that both conductors make perma- nent contact with the screw terminal. SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Commissioning General Notes Changing the Polarity-Reversal Frequency LEDs SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
To allow temperature equalization and to avoid moisture and condensation when placing the device in service for the first time or after it was in storage for a lengthy period, Siemens recommends leaving the device for a minimum of 2 hours in the operating area before using it.
Unscrew and remove each of the 2 screws at the bottom and top Z-shaped angle brackets used to fasten ² the device to the switch panel. Remove the device from the switch panel. ² SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
5.2.3 Setting the Frequency You can set the polarity-reversal frequency (frequency of the square-wave generator) using the DIP switch S1 on the printed circuit board assembly. SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 95
Board Assembly. If you have disconnected the conductors from the junction block, reconnect the conductors to the screw ² terminals. Make sure that the wiring is correct. Commission the device. ² SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 96
Label for the Set Frequency NOTE If the 7UM62/7UM85 does not display correct values, repeat the frequency setting on the injection unit 7XT71 until the values roughly correspond to the required operating conditions. SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Table 5-1 Operating States Signaled by LEDs Meaning Device ready ERROR Device not ready SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 98
SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Maintenance and Repair 6.1 Maintenance Maintenance The injection unit 7XT71 is maintenance-free. Wipe the device using a clean, dry, and soft cloth if necessary. Do not use solvents. SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
7XT71 and these may only be replaced by the manufacturer according to the directives for electrostatic sensitive devices (ESD). If you suspect a defect in the device, Siemens recommends sending the entire device to the plant of the ²...
Seite 102
Board Assembly. If you have disconnected the conductors from the junction block, reconnect the conductors to the screw ² terminals. Make sure that the wiring is correct. Commission the device. ² SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
+10 °C to +35 °C. In case of longer storage periods, Siemens also recommends connecting the device to auxiliary voltage once a year for 1 to 2 days in order to form the electrolytic capacitors used. This procedure should also be executed before operating the device.
REACH/RoHS Declaration You can find our current REACH/RoHS declarations at: https://www.siemens.com/global/en/home/products/energy/ecotransparency/ecotransparency-down- loads.html NOTE You can find more information about activities and programs to protect the climate at the EcoTransparency website: https://www.siemens.com/global/en/home/products/energy/ecotransparency.html SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 106
SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
7XP20, 1/6 19” housing Measurements (W x H x D) 7XT7100-0BA00 312.8 mm x 75.0 mm x 243.5 mm (12.31 in x 2.95 in x 9.59 in) with Z-shaped angle brackets and junction block SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 109
2.3 kg 7XT7100-0EA00 2.1 kg Degree of protection according to EN 60529: Front side IP51 Housing and terminals IP20 Firmware Version in the Protection Device 7UMxx 7UM85 ≥ V07.30 7UM62 ≥ V04.70 SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
400 pulses per second; Test duration: 2 s, Ri = 200 Ω Electrostatic discharge test, test IEC 61000-4-2 8 kV contact discharge 15 kV air discharge both polarities; 150 pF; Ri = 330 Ω SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 111
IEC 61000-6-4 (generic standard) Radio disturbance voltage on lines, auxiliary voltage 150 kHz to 30 MHz, limit class A only, IEC-CISPR 22 Disturbance-field strength IEC-CISPR 11 30 MHz to 1000 MHz limit class A SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Rated auxiliary alternating voltage + 10 % -5 °C to +55 °C Limiting temperature During storage -25 °C to +55 °C During transport -25 °C to +70 °C Storage and transport using factory packaging SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 113
Up to 95 % relative humidity on 56 days a year; no condensation permissible during operation! Siemens recommends installing all devices so that they are not exposed to direct sunlight nor subject to large fluctuations in temperature that may cause condensation to form.
Seite 114
SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Appendix Ordering Information and Accessories Block Diagram Connection Diagrams Revision History SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Ordering Information and Accessories Order Code [scordcod, 1, en_US] Figure A-1 Order Code Accessories Covering Cap for Terminal Type Order Number Voltage terminal, 18-pin, 12-pin C73334–A1–C34–1 Current terminal, 12-pin, 8-pin C73334–A1–C33–1 SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Block Diagram, Injection Unit 7XT71 NOTICE The voltage between terminal 1 and terminal 2 must not exceed AC 300 V. Disregarding this may lead to material damage. Use appropriate safety measures. ² SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Connection Diagrams with the Resistor Unit 7XR8004 [dw_7xr8004 connex1, 2, en_US] Figure A-3 Connection Example for Excitation Using ß [dw_7xr8004 connex2, 2, en_US] Figure A-4 Connection Example for Excitation Using Rotating Rectifiers SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 119
Connection Diagrams with the Resistor Unit 7XR8004 or 7XR6004 [le_7xr8004_6004, 1, --_--] Figure A-5 Connection Diagram for Excitation Voltages < DC 850 V Terminal assignment for 7XR8004 Terminal assignment for 7XR6004 SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 120
Appendix A.3 Connection Diagrams [le_7xr8004_6004_less_dc, 1, --_--] Figure A-6 Connection Diagram for Excitation Voltages < DC 1200 V Terminal assignment for 7XR8004 Terminal assignment for 7XR6004 SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
7XT7100-0EA00/DD Housing revision New 18-pin screw terminal, Attention: The connections have changed. Possible to connect 2 devices 7UM62/7UM85 7XT7100-0BA00/EE Improvement to the firmware 7XT7100-0EA00/EE Product information updated with SIPROTEC 5 7UM85. SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...
Seite 122
SIPROTEC 4/5, Injection unit 7XT71, Manual C53000-B1174-C128-8, Edition 05.2020...