Bosch FSA 740 Edition Originalbetriebsanleitung Seite 24

en en 24 | FSA 740 Edition | Operation
5. Operation
5.1 Switch-on/switch-off
Switch on or off FSA 740 Edition at the central power
switch on the back of the unit (fig. 2, item 5).
i
Before switching off the device, shut down the PC
using the Windows operating system. Leave the PC
switched off for at least 60 seconds before switching
on again.
i
When operating the FSA 740 Edition, faults may
occur if a PC or other components (e.g. mouse,
connecting cables) from suppliers other than Bosch
are used.
5.2 Notes on measurement
DANGER – Risk of electric shock if measure-
ments are taken on motor vehicles without
connecting cable B–!
Measurements taken with connecting cable
B– not connected to vehicle ground or the
battery negative terminal will result in injury,
heart failure or fatal electric shocks.
¶
For all measurements, connect the
FSA 740 Edition by way of connecting
cable B– to vehicle ground or the battery
negative terminal.
DANGER – Risk of electric shock from ex-
cessively high measurement voltage!
The measurement of voltages in excess of
60 V DC/30 V AC/42 V ACpeak using CH1/
CH2 multi measurement cables will result in
injury, heart failure or fatal electric shocks.
¶
Never use CH1/CH2 multi measurement
cable to measure mains or similar voltag‑
es.
!
Measurements with FSA 740 Edition are allowed only
in a dry environment.
!
The FSA 740 Edition is not to be used for measur‑
ing isolation from the supply on electric and hybrid
vehicles. Measurements on high‑voltage capacitor
ignitions are not allowed as voltage values greater
than 300 Volt may occur in this type of ignition.
!
Measurements on the passenger car piezo common
rail injector are only permitted with special adapter
cables (optional accessories).
!
The test prods supplied with the test prod set
(1 687 010 153) can only be used for measurements
below 30 volts.
1 689 989 311 | 2017-03-06
Basic approach to measurements on the vehicle:
1. Switch off the ignition.
2. Connect FSA 740 Edition to the battery (B–) or en‑
gine ground via the connecting cable B–.
3. Connect the required measurement cables to the
vehicle.
!
During a measurement, do not hold the measure‑
ment cables by hand.
4. Switch on ignition.
5. Perform the measurements.
6. Switch off the ignition after measuring.
7. Disconnect the measurement cables from the vehi‑
cle.
8. Disconnect the connecting cable B–.
"
Measurement complete.
5.3 DSA, diagnostics software selection
DSA enables you to:
R
Start Bosch applications (automatically as well).
R
Configure interface settings.
R
Select language for DSA and Bosch applications.
R
Install software.
R
Release component test and vehicle‑specific infor‑
mation.
R
Update customer and vehicle data.
R
Close Bosch applications.
i
Perform software installation via the DSA, diagnos‑
tics software selection. Note installation information
on respective CD/DVD.
Further information is available in the DSA online Help.
5.4 Install BEA-PC software
i
See the installation instructions provided with the
respective software for additional information con‑
cerning installation and update of the Bosch Emis‑
sions Analysis software "BEA‑PC" software.
5.5 ESI[tronic] 2.0
i
Each current version of ESI[tronic] 2.0 is included
in the scope of delivery of the DVD. Before you can
operate ESI[tronic] 2.0, you must first install and
release the software. How to install and enable the
ESI[tronic] 2.0 and the ESI[tronic] 2.0 release is
described on the "ESI[tronic] 2.0 DVD 1 Diagnosis
and technology" in the directory 'DOCS\SETUP\
INFO_XXX.PDF'.
Robert Bosch GmbH