Stiga 85 Combi Gebrauchsanweisung Seite 32

Downloaded from www.Manualslib.com
EN
1. Place the deck in position in front of the ma-
chine.
2. Check that the deck mounts are installed on the
machine as follows.
• Washer (3:D). Only machines up to and in-
cluding 2006.
• Deck mount (3:C).
• Washer (3:B).
• Circlip (3:A).
3. Screw the arms into each other. See fig. 5.
4. Remove the belt cover (6:H) by loosening the
screws 6:I.
5. Loosen the belt guide screws (7, 8:K) a couple
of turns.
6. Set the maximum cutting height.
7. Work off the belt from the cutting deck pulley.
8. Fit the belt to the machine pulley and after that
to the cutting deck pulley.
9. Tighten the belt guide screws (7, 8:K).
10.Tension the belt as follows.
Park 4WD:
Grip the belt tensioner's lever with your left
hand. Pull the lever and apply the tensioner to
the outside of the belt with your right hand. See
fig.9.
Villa, Ready:
Tension the belt with the belt idler. The belt
idler should be on the inside of the belt and pull
out to the left (viewed from the driver's posi-
tion). See fig. 11.
11.Install the belt cover (6:H) with the screws (6:I).
12.Suspend the unit in the implement lifter. See
fig. 13.
13.Perform the cutting deck basic setting. See 3.5.
14.If the deck has electrical cutting height adjust-
ment, connect the cable to the machine's front
right socket. See fig. 16.
3.2 Park 2WD with fixed deck con-
nections
Example of fixed deck connections, see 3:C and
4:G.
1. Place the deck in position in front of the ma-
chine.
2. Check that the deck mounts are installed on the
machine as follows.
• Deck mount (4:G).
• Washer (4:F).
• Lock pin (4:E).
3. Screw the arms into each other. See fig. 5.
4. 5.Set the maximum cutting height.
5. Locate the belt around the machine's belt pul-
ley.
6. Tension the belt as follows.
32
manuals search engine
ENGLISH
Tension the belt with the belt idler. The belt
idler should be on the left side of the belt
viewed from the driver's position. See fig. 10.
7. Suspend the unit in the implement lifter. See fig.
13.
8. Perform the cutting deck basic setting. See 3.5.
9. If the deck has electrical cutting height adjust-
ment, connect the cable to the machine's front
right socket. See fig. 16.
3.3 Machines with quick connec-
tions
Example of quick connections, see fig. 12.
1. Place the deck in position in front of the ma-
chine.
2. Check that the quick connections are fitted to
the machine according to their supplied sepa-
rate instruction.
3. Check that the deck arms are screwed into place
in the quick connections. If this is not the case,
screw them into place. See fig. 12.
4. Set the maximum cutting height.
5. Set the quick connections in their rear positions.
See their supplied separate instruction.
6. Fit the belt on to the machine pulley.
7. Tension the belt as follows.
Park 4WD:
Grip the belt tensioner's lever with your left
hand. Pull the lever and apply the tensioner to
the outside of the belt with your right hand. See
fig.9.
Park 2WD:
Tension the belt with the belt idler. The belt
idler should be on the left side of the belt
viewed from the driver's position. See fig. 10.
8. Set the quick connections in their front posi-
tions. See their supplied separate instruction..
9. Suspend the unit in the implement lifter. See fig.
13.
10.Perform the cutting deck basic setting. See 3.5.
11.If the deck has electrical cutting height adjust-
ment, connect the cable to the machine's front
right socket. See fig. 16.
3.4 Tyre pressure
Adjust the tyre pressures according to the table be-
low.
Machine Pressure (bar/psi)
Front
Park 0,6/9
Villa 0,4/6
Ready 0,4/6
Rear
0,4/6
1,2/17
1,2/17