Technical Data; Noise/Vibration Information; Battery Charging - Bosch GOP 18V-28 Professional Originalbetriebsanleitung

18 | English
(2) Ventilation slots
A)
(3) Battery
(4) Orbital stroke rate preselection thumbwheel
(5) SDS lever for unlocking tools
(6) Tool holder
(7) Worklight
A)
(8) Battery release button
(9) Clamping lever for depth stop
A)
(10) Depth stop
A)
(11) Plunge cut saw blade
(12) Handle (insulated gripping surface)
A)
(13) Dust extraction system
A)
(14) Sanding plate
A)
(15) Sanding sheet
(16) Clamping lever for dust extraction system
A)
(17) Dust extraction outlet
A)
(18) Dust extraction adapter
A)
(19) Dust extraction hose
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical data

Cordless multi-cutter
Article number
Rated voltage
No-load speed n
0
Oscillation angle on left/right
Weight according to
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
B)
ure during operation and
during storage
Recommended rechargeable
batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Technical data determined using the battery that comes with the
product.

Noise/Vibration Information

Noise emission values determined according to
EN 62841‑2‑4.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 84 dB(A); sound power level
95 dB(A). Uncertainty K = 3 dB.
1 609 92A 5NM | (04.06.2020)
Wear hearing protection!
Vibration total values a
determined according to EN 62841‑2‑4:
Sanding: a
Cutting with plunge cut saw blade: a
Cutting with segmential saw blade: a
K = 1.5 m/s
Scraping: a
The vibration level and noise emission value given in these
A)
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
A)
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
GOP 18V-28
and organising workflows correctly.
3 601 HB6 0..
V= 18
Fitting
-1
min 8000–20000
u
° 1.4
A)
kg 1.5–2.6
°C 0 to +35

Battery Charging

°C −20 to +50
u
GBA 18V...
Note: The battery is supplied partially charged. To ensure
ProCORE18V...
full battery capacity, fully charge the battery in the charger
GAL 18...
before using your power tool for the first time.
GAX 18...
The lithium-ion battery can be charged at any time without
GAL 36...
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
The battery (3) is equipped with two locking levels to pre-
vent the battery from falling out if the battery release button
(triax vector sum) and uncertainty K
h
2
= 3.5 m/s , K = 1.5 m/s
h
2
,
2
= 8.5 m/s , K = 1.5 m/s
h
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
2
,
2 2
= 8 m/s , K = 1.5 m/s ,
h
2
= 5.5 m/s ,
h
2
.
Bosch Power Tools