Bosch GOP 18V-28 Professional Originalbetriebsanleitung Seite 21

Application tool
saw blade for wood
and metal
ACZ 105 ET
Starlock
105 mm diameter
carbide segment
saw blade for
multi-material
ACZ 100 SWB
Starlock
100 mm diameter
bimetal segment
serrated knife for
multi-material
ACZ 85 RD4
Starlock
85 mm diameter
Diamond-RIFF seg-
ment saw blade for
mortar and abras-
ive materials
AVZ 70 RT4
Starlock
70 mm wide
carbide-RIFF mor-
tar remover
AVZ 90 RT2
Starlock
90 mm wide
carbide-RIFF delta
plate for mortar
and abrasive ma-
terials
AVZ 93 G
Starlock
93 mm-wide sand-
ing plate for sand-
ing sheets of the
Delta 93 mm series
AUZ 70 G
Starlock
70 mm wide profile
sander for
70 × 125 mm
sanding sheets
AVZ 32 RT4
Starlock
32 × 50 mm
carbide-RIFF sand-
ing finger for wood
and paint
Bosch Power Tools
Material Application
Example: Shortening already installed skirting boards or
door frames, plunge cuts when adapting floor panels
Fibre cement boards, tile Separation and plunge saw cuts; also for sawing close to
joints, brick, fibreglass-re- the edge in difficult-to-access areas; long service life
inforced plastics, lamin- thanks to BOSCH carbide technology;
ate Example: Shortening already installed skirting boards or
door frames, milling cable ducts in brick, quick and low-
dust cutting out of tile joints, cutting fibreglass boards to
size for fittings, adjustment work in laminate; available
from mid-2021
Insulation material, insula- Precise cutting of soft materials;
tion boards, floor panels, example: Cutting insulation boards to size, cutting pro-
impact sound insulation truding insulation material to length so that it is flush with
boards, cardboard, car- the surface
pets, rubber, leather
Cement joints, soft wall Cutting and separating in areas and corners that are close
tiles, fibreglass-reinforced to the edge or difficult to access, extra long service life
plastics, epoxy, GKF thanks to Diamond-RIFF;
Example: Removing joints between wall tiles for repair
work, recesses in tiles;
also available as Carbide-RIFF version: ACZ 85 RT3 for
normal joints, ACZ 70 RT5 for thin joints
Mortar, joints, epoxy Reaming and separating joint and tile material, as well as
resin, fibreglass-rein- rasping and sanding on a hard substrate; long service life
forced plastics, abrasive thanks to BOSCH carbide technology;
materials Example: Removing tile adhesive and grout
Mortar, concrete residue, Rasping and sanding on a hard substrate;
wood, abrasive materials, Example: Removing mortar or tile adhesive (e.g. when re-
paint placing damaged tiles), removing carpet adhesive
residues, removing paint residues;
available in grain sizes 20 (RT2), 40 (RT4), 60 (RT6) or
100 (RT10)
Depends on the sanding Sanding on edges, in corners or in difficult-to-access
sheet areas;
depending on sanding sheet, e.g. for sanding wood, paint,
lacquer, stone;
non-woven materials for cleaning and for structuring
wood, removing rust from metal and for abrading lac-
quers, polishing felt for pre-polishing
Wood, pipes/profiles, Convenient and efficient sanding of profiles and curved,
paint, varnish, filler, metal uneven material surfaces up to a diameter of 55 mm;
sanding sheets for sanding wood, pipes/profiles, varnish,
filler and metal
Wood, paint Sanding wood or paint in difficult-to-access places without
sanding paper; long service life thanks to BOSCH carbide
technology;
Example: Sanding down paint between window shutter
slats, sanding wooden flooring in corners;
available in grain sizes 40 (RT4) and 100 (RT10)
English | 21
1 609 92A 5NM | (04.06.2020)