Vitek VT-1207 BN Betriebsanweisung Seite 5

Note:
While the first switching the heating ele-
–
ment burns, therefore occurrence of a small
amount of smoke or extraneous smell is pos-
sible, it is normal.
Water spray
You can dampen the fabric by pressing the
–
spray button (5) several times (pic. 4).
Make sure that there is enough water in the
–
water tank (10).
Dry ironing
Place the iron on its base (8).
–
Insert the power plug into the socket.
–
Turn the temperature control knob (11) to set
–
the required ironing temperature: «•», «••»,
«•••» or «MAX» (pic. 3), depending on the
type of fabric, the pilot lamp (9) will light up.
Set the continuous steam supply knob (3) to
–
the position «
is off) (pic. 5).
When the soleplate temperature reaches the
–
desired temperature value, the pilot lamp (9)
will go out, you can start ironing.
After you finish ironing set the temperature
–
control knob (11) to the "MIN" position.
Pull the plug out of the socket and let the iron
–
cool down completely.
Steam ironing
The iron has an anti-drip valve that stops water
supply, when the soleplate temperature is too
low; it prevents dripping from the soleplate
openings (14). During heating and cooling of
the iron soleplate you will hear corresponding
clicks of anti-drip valve opening/closing that
indicates its normal operation.
Place the iron on its base (8).
–
Insert the power plug into the socket.
–
Make sure that there is enough water in the
–
water tank (10).
Turning the knob (11) set the desired temper-
–
ature value in the steam ironing zone "MAX",
the pilot lamp (9) will light up.
When the soleplate (14) temperature reaches
–
the desired temperature value, the pilot lamp
(9) will go out, you can start ironing.
Turn the continuous steam supply knob (3) to
–
set the steaming rate, steam will start outgo-
ing from the soleplate (14) openings.
VT-1207.indd 5
» (continuous steam supply
After finishing the operation set the tempera-
–
ture control knob (11) to the "MIN" position,
and the continuous steam supply knob (3)
to the position « » (continuous steam sup-
ply is off).
Pull the plug out of the socket and let the iron
–
cool down completely.
ATTENTION!
If steam is supplied not continuously, check the
correct position of steam supply knob (3) and
water level in the water tank (10).
ADDITIONAL STEAM SUPPLY
Additional steam supply function is useful
when ironing of folds and can only be used
at high ironing temperatures (when the iron
temperature control knob (11) is set to "MAX").
When pressing the additional steam supply
button (4) steam will go out of the soleplate
intensively (pic. 6).
Note:
In order to avoid water leakage from steam
–
openings, press the additional steam supply
button (4) with a 4-5 sec. interval.
Vertical steaming
Vertical steaming function can be used only
at high ironing temperatures (when the iron
temperature control knob (11) is set to "MAX").
Hold the iron vertically at the distance of 10-30
cm from the clothes, press the additional steam
supply button (4) with a 4-5 seconds interval,
steam will be supplied from the soleplate (14)
intensively.
Important information
– Vertical steaming is not recommended for
synthetic fabrics.
– To avoid fabric burning, do not touch it with
iron soleplate while vertical steaming.
Never steam clothes on a person as the
–
steam temperature is very high, use a hang-
ers or a stand.
After you finish ironing, switch off the unit,
–
wait until it cools down completely, then open
the water inlet lid (2), turn over the iron and
drain the remaining water (pic. 8).
5
ENGLISH
16.10.2012 15:16:36