Werbung
alphanumeric code, with less than 4 digit,
is entered on the keypade, the system
automatically fills the empty numbers with
zeros, for instance entering only the code
"E" and press
the display shows the
code "E000" and the system transmits
the code 5000. In the same way if the
code "E2" is entered the display shows
"E002" and the system transmits the code
5002, therefore the user you want to be
identified by the code "E002" must be
programmed as user 5002.
Personalisation of display initial text
(code 04)
You can modify the text shown on the
display during normal operation or idle
state. For visualization you must set bit 4
or bit 5 with value "1" (see "system
programming").
To insert a personalized text:
PROG to enter the
press the button
programming mode;
enter the code 04 and press the button
; the display shows "FARNET ", in
case of first programming, or the text
you want to replace;
for information on how to enter the
characters see "entry of names";
press
to confirm; the display shows
"Programming / type: ";
continue by entering the code of a new
programming function or press the but-
PROG to exit.
ton
Loading names from PC (code 05)
You can load names directly from your
PC.
Load the names on the PC using a
dedicated software application
( software supplied on demand ).
Turn off the push-button panel and the
PC.
Connect the PC serial port to the stereo
jack (PC) on the back of the push-
button panel with a cable as shown in
the figure.
PC serial port
1
6
2
7
3
8
4
9
5
TD4100PL
Turn on the PC and then the push-
button.
Enter the code 05 and press the
button
"TD4100PL ---- PC / in progress....0".
Download the names from the PC
within 15 seconds; the display shows
"TD4100PL ---- PC / in progress....1",
" TD4100PL ---- PC / in progress....2"
and then the downloaded names.
At the end of download the push-
button deletes the existing names.
The first line of the display shows
"waiting" and the second line shows a
status bar to show the progress of the
deletion operation.
At the end the display shows
"Programming / type: " .
Turn off the push-button panel and
then the PC.
Disconnect the cable from the PC
and the push-button panel.
Ordering names (code 06)
You can list the names in alphabetical
order (from A to Z).
Press the button
programming mode.
Enter the code 06 and press the
button
shows "waiting" and the second line
shows a status bar; at the end of the
operation the push-button panel re-
turns automatically to the program-
ming mode (the display shows "Pro-
gramming / type: " ).
Continue by entering the code of a
new programming function or press
the button
Inserting the external door station
address PE (
You can code the external door station
address with codes from 9950 to 9979.
Press the button
programming mode.
Stereo jack
Enter the code 10 and press the
Ø = 2,5mm
button
DRESS PE ".
3
Dial the coding number for the door
2
station and press the button
confirm.
5
Continue by entering the code of a
new programming function or press
5
the button
2
3
; the display shows
PROG to enter the
; the first line of the display
PROG to exit.
code 10 )
PROG to enter the
; the display shows " AD-
to
PROG to exit.
Inserting the button address P1
(code 11)
To save an extension number and call it
directly from a button connected between
terminals P1 and -:
press the button
PROG to enter the
programming mode;
enter the code 11 and press the button
; the display shows " ADDRESS
P1 ";
dial the extension number. Extensions
must be coded with numbers from
0000 to 9899;
press the button
to confirm;
press the button PROG to exit the
programming mode.
Return to operation mode
Press the button PROG at the end of
programming; the display shows
" FARFISA / dial the number or press
" or the text you have entered during
programming (see "Personalisation of
display initial text").
12
Mi 2373
Werbung
