Before Starting The Equipment - EINHELL GE-CM 36/43 Li M Originalbetriebsanleitung

Warning!
This equipment generates an electromag-
netic fi eld during operation. Under certain
circumstances this fi eld may actively or pas-
sively impede medical implants. To reduce
the risk of serious or fatal injuries, we recom-
mend persons with medical implants to con-
sult their doctor and the manufacturer of the
medical implant prior to using the equipment.

5. Before starting the equipment

The lawn mower is delivered partly assembled.
The push bar and the grass basket must be as-
sembled before using the lawn mower. Follow the
instructions step by step and refer to the pictures
when assembling.
Important! Required assembly parts (screws,
cable guides, etc.) or functional parts (e.g. plugs,
wrenches, etc.) can be found in the molded parts
of the packaging or on the equipment.
Mounting the push bar (Fig. 3 to 6).
Insert the push bar holder (Item 3) into the hand-
lebar mount and secure with the quick clamping
function (Item 11) (Fig. 3). The top push bar (Item
2) must be pushed onto the push bar holders
(Item 3) and secured as shown above in Fig. 4.
Then attach the power cable to the push bar (Fig.
5) using the cable clips (Item 13). Now you can
select the push bar height in three stages (Fig. 6/
Item A).
Note!
The handle height may be adjusted only within
the marked range.
If necessary, turn the respective quick-release
fastener back suffi ciently on the thread so that the
quick-release lever (Fig. 6/Item 11) can then be
fl ipped towards the back.
•
Press in the long handle and secure in the
desired position using the quick clamping
function (Fig. 6/Item 11)
Warning!
Always set the identical handle height on both
sides.
•
Use the cable clips to align the cable to the
long handle (Fig. 5/Item 13)
Fitting the grass box (see Figs. 7 to 9)
First plug the lower part of the housing (Item
Anl_GE_CM_36_43_Li_M_SPK9.indb 23 Anl_GE_CM_36_43_Li_M_SPK9.indb 23
GB
15) and the right part of the housing (Item 18)
together as shown in Fig. 7. Then plug the top
part of the housing (Item 17) onto the previously
assembled parts (Fig. 8).Before you fi t the grass
basket you must ensure that the motor is swit-
ched off and the blade is not rotating. Lift the
ejector fl ap (Item 7) with one hand. With the other
hand, hold the grass basket by the handle and
hook it in from above (Fig. 9).
Filling level indicator of the grass collector
The grass box is equipped with a fi lling level in-
dicator (Fig. 2/Item 16). which is opened by the
airfl ow that the lawn mower generates during ope-
ration. If the fl ap closes during mowing, the grass
collecting device is full and must be emptied. To
ensure the proper functioning of the fi lling level
indicator, the holes under the fl ap must always be
kept clean and passable.
Adjusting the cutting height
Caution!
Adjust the cutting height only when the machine
has been switched off and the safety plug has
been pulled out.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged. To prevent any imbalance, replace
blunt and/or damaged blades. To carry out this
check, fi rst switch off the motor and pull out the
safety plug.
The cutting height is adjusted as follows (see Fig.
10):
1. Push the lever (A) outwards.
2. Set the lever (B) to the desired cutting height.
3. Release the lever (A) and check that it is se-
curely seated in the lock.
Reading off the cutting height
The cutting height can be set between 25-75 mm
in 6 intervals, and can be read off on the scale
(Fig. 12/D).
Using the mulching adapter (Fig. 11)
In mulching mode the cuttings are shredded in
the enclosed mower housing and then spread
back onto the lawn. It is not necessary to gather
and dispose of the grass.
Notice! Mulching is only possible if the lawn is
relatively short.
- 23 -
21.10.2019 06:22:23 21.10.2019 06:22:23