EMV-Richtlinie entsprechen. In unserem EMV-Labor, das von der DATech für Prüfungen der elektromagnetischen Verträglichkeit akkreditiert ist, wurde der Nachweis erbracht, dass die Balluff-Produkte die EMV-Anforderungen der Norm EN 60947-5-2 erfüllen. Applikation Nur für Applikationen nach NFPA 79 (Maschinen mit einer Versorgungsspannung von max.
IO-Link Daten IO-Link Master Übertragungsrate 38,4 kbit/s (COM2) Minimale Zykluszeit 2,3 ms Wir empfehlen die Verwendung von IO-Link Mastern der Firma Balluff. Mechanisch Anschlussart Sensortausch Kabel mit Steckverbinder M8, 3-polig, 0,2 m Stecker M8, 3-polig Wir weisen darauf hin, dass nach dem Sensortausch unter Werkstoff Gehäuse...
Function Mode 0x01 (1) = One shot 0x02 (2) Delay Time 1 UINT16 0x0000….0xFFFF milliseconds (On delay) (0…65535) 0= timing function off 0x03 (3) Delay Time 2 0x0000..0xFFFF milliseconds (Off delay, One (0…65535) shot) 0= timing function off www.balluff.com deutsch...
Auslesen und Überprüfen des Parameters Teach-In Status mit Index 0x003B. Zugriff Index Wert Bedeutung Ergebnis 0x003B 0x01 SP1 erfolgreich übernommen. Teach-In Teach-In State = SP1 SUCCESS erfolgreich (0x01) beendet 0x07 Teach-In State = ERROR Zurück zu Schritt 2 www.balluff.com deutsch...
Seite 12
Optoelektronische Sensoren Rotlicht Lichttaster mit Hintergrundausblendung einstellbar über IO-Link BOS Q08M-UUI-KH22-... Statisches Teach-In mit 2 Teach Punkten Prinzip 3. Überprüfen, ob TP1 erfolgreich eingelernt wurde: Auslesen und Überprüfen des Parameters Teach-In Schaltpunkt SPy wird durch Einlernen von zwei Teach Status mit Index 0x003B. Punkten (TP1 und TP2) ermittelt.
Seite 13
6. Überprüfen, ob SP1 erfolgreich übernommen wurde: Auslesen und Überprüfen des Parameters Teach-In Status mit Index 0x003B. Zugriff Index Wert Bedeutung Ergebnis 0x003B 0x01 SP1 erfolgreich übernommen. Teach-In Teach-In State = SP1 SUCCESS erfolgreich (0x01) beendet 0x07 Teach-In State = ERROR Zurück zu 1 www.balluff.com deutsch...
Optoelektronische Sensoren Rotlicht Lichttaster mit Hintergrundausblendung einstellbar über IO-Link BOS Q08M-UUI-KH22-... Dynamisches Teach-In (Beide Schaltpunkte) Prinzip 2. Warten bis mindestens 1 Prozesszyklus im Lichtweg stattgefunden hat. Das dynamische Teach-In wird Das dynamische Teach-In ermöglicht die Schaltpunkt- automatisch beendet, wenn während >1 min kein einstellung, ohne den Prozess anzuhalten.
Seite 15
BOS Q08M-UUI-KH22-... User's Guide english...
Seite 16
EMC Law. In our EMC Laboratory, which is accredited by the DATech for Testing of Electromagnetic Compatibility, proof has been documented that these Balluff products meet the EMC requirements of the harmonized standard EN 60947-5-2. Application...
Seite 17
IO-Link Data conditions. Transmission rate 38.4 kbit/s (COM2) Minimum cycle time 2.3 ms IO-Link master Mechanical We recommend the use of Balluff IO-Link Masters. Connection type Cable with connector M8, 3-pin, 0.2m Connector M8, 3-pin Sensor replacement Housing material GD-Zn nickel plated...
Photoelectric Sensors Red light diffuse reflective with background supression and IO-Link BOS Q08M-UUI-KH22-... Process data Smart Sensor Profile Output data Sensor transmits 1 octet of process data to Master. (Process Data In: 1 Byte, M-Sequence Type: TYPE_2_1) Byte 0 BDC1 Switching point information: "1"...
Seite 19
Function Mode 0x01 (1) = One shot 0x02 (2) Delay Time 1 UINT16 0x0000….0xFFFF milliseconds (On delay) (0…65535) 0= timing function off 0x03 (3) Delay Time 2 0x0000..0xFFFF milliseconds (Off delay, One (0…65535) shot) 0= timing function off www.balluff.com englisch...
Photoelectric Sensors Red light diffuse reflective with background supression and IO-Link BOS Q08M-UUI-KH22-... Events Event Meaning Mode Type Instance DeviceStatus Remark Code 0x4210 Temperature appears/disappears Warning Application Out-of-Specification >≈ 60 °C (U = 24 V) Overrun 0x5111 Supply appears/disappears Warning Application Out-of-Specification <...
Seite 23
5. Verify correct acceptance of SP1: Read and verify parameter Teach-In Status with Index 0x003B. Access Index Value Meaning Result 0x003B 0x01 SP1 accepted successfully. Teach-In Teach-In State = SP1 SUCCESS successful (0x01) Teach-In State = ERROR Back to 2 0x07 www.balluff.com englisch...
Seite 24
Photoelectric Sensors Red light diffuse reflective with background supression and IO-Link BOS Q08M-UUI-KH22-... Static Teach-In with 2 teach points Principle 3. Verify correct setting of TP1: Read and verify parameter Teach-In Status with Index Setpoint SPy is set to mean value of the two teach points 0x003B.
Seite 25
Precondition: Sensor is installed, aligned to the running process and operated in IO-Link mode. Procedure: 1. Start Dynamic Teach: Send System command 0x47 to sensor. Access Index Value Remark 0x002 (2) 0x47 SP1 Dynamic Teach Start www.balluff.com englisch...
Seite 26
Photoelectric Sensors Red light diffuse reflective with background supression and IO-Link BOS Q08M-UUI-KH22-... Dynamic Teach-In of both setpoints 2. Wait for a minimum of one process cycle is completed. Principle ( Dynamic Teach is aborted in case no object has been Dynamic teach-in allows you to set the switching point detected within 1 min or Teach has not been confirmed without interrupting the process.
Seite 28
US Service Center CN Service Center Germany Germany China Balluff GmbH Balluff GmbH Balluff Inc. Balluff (Shanghai) trading Co., ltd. Schurwaldstrasse 9 Schurwaldstrasse 9 8125 Holton Drive Room 1006, Pujian Rd. 145. 73765 Neuhausen a.d.F. 73765 Neuhausen a.d.F. Florence, KY 41042 Shanghai, 200127, P.R.