NAD 710 Bedienungsanleitung Seite 6

GB
8. DUAL VOLUME CONTROL
The dual concentric volume knob combines the func-
tions of Volume and Balance Control. The outer ring
controls the level to the right-hand speaker and the
inner section controls the level of the left-hand speaker.
The two are friction-coupled so that they always move
together when the volume control is adjusted.
To alter the balance between the two speakers, hold
the outer ring and manually adjust the relative position
of the VOLUME CONTROLs center section.
Adjusting the VOLUME CONTROL does not affect
recordings made using the TAPE or PORTABLE out-
puts.
TUNER AND DISPLAY PANEL.
9. STEREO and CENTER TUNE INDICATORS
The CENTER TUNE indicator lights when you are
correctly tuned to the station. The FM STEREO indica-
tor lights when a stereo FM station is being received
and the NAD-710 is switched into STEREO mode.
10. DISPLAY PANEL
The Display Panel is active all the time the NAD-710
is on and displays the frequency of the station that the
tuner section is currently set to. When switching to
STORE or PRESET Modes the display will flash for a
few seconds, alternately showing the current Preset
number and the station's frequency.
11. MODE SWITCH AND INDICATORS
The MODE button switches the tuner into either
Tune, Preset or Search Modes. The indicator lights
show which mode the Tuner section is currently in.
Tune Mode is for manually tuning onto a radio sta-
tion.
Preset Mode is to call up stations already stored in
the NAD-710's presets.
Search Mode will automatically search through the
tuning frequencies and stop when it finds a broadcast
station.
12. AM/FM
Press the AM/FM button to switch the NAD-710
between FM and AM (Medium wave) tuning. The
Display Panel shows the frequency of the tuned station
in MHz for FM and kHz for AM.
13. STORE
Press STORE to program a station into one of the
NAD-710's twelve FM or twelve AM Preset memories.
To Store a station as a Preset, first select FM or AM
and then tune to the station's frequency using Search
or Tune Mode. Press STORE once and the display will
flash, showing the station frequency and the current
Preset number. Use the
Preset number you want to assign the station to. Press
STORE again and the station will be programmed into
that preset number.
14. LOCK
Pressing LOCK fine-tunes the NAD-710 into the sta-
tion's frequency.
NAD
6
buttons to choose the
15. TUNE
Use the TUNE buttons for tuning to the required
station and to select Preset stations. In Tune Mode,
pressing the or buttons increases or decreases
the tuning frequency. Holding the button down quickly
scans through the frequencies.
The CENTER TUNE indicator will light when a station
is correctly tuned.
In Preset Mode, the and
select radio stations stored in the tuners Preset memo-
ries.
TUNING AM & FM STATIONS.
Use TUNE mode to select a known station's frequen-
cy. SEARCH mode automatically looks for stations that
are transmitting in your area.
TUNE MODE.
First select the AM or the FM band using the AM/FM
button.
Press the MODE button until the TUNE indicator
lights up. Press the or
locating a frequency. Holding the
down will move quickly through the frequency range.
When the required station has been located press
LOCK to exactly tune to the station's frequency.
SEARCH MODE.
First select the AM or the FM band using the AM/FM
button.
Press the MODE button until the SEARCH indicator
lights up. Press the or
searching through the frequency band. When the tuner
finds a broadcast signal of adequate strength, the auto-
matic search will stop at that station. Press the
buttons again to continue searching for stations.
Pressing the or buttons at any time will manually
stop the search. When the required station has be
located, press LOCK to exactly tune to the station's fre-
quency.
STORING AND RECALLING PRESET AM & FM
STATIONS.
To store a station as a Preset, first tune to the
required frequency using either Search or Tune.
Press the STORE button. The Display Panel will
show the current Preset number for approximately 5
seconds. Press or to select a different Preset
number to store the station, if required.
Press the STORE button again to store the station's
frequency as the chosen Preset number. The NAD-710
will then revert to normal operation.
The Preset information will be permanently held in
memory unless you store another station over it.
To exit the Memory mode without storing a station,
leave all the controls untouched; the Store mode will
automatically cancel itself after approximately 5 sec-
onds.
RECALLING A PRESET STATION.
First select the AM or the FM band using the AM/FM
button and then press the Mode switch until the PRE-
buttons are used to
buttons to start manually
or buttons
buttons to start the tuner
or