Nuts And Bolts; Adjusting The Converter Cable; Occasional Maintenance; Cutting Means - Stiga MP2 504 Serie Bersetzung Der Originalbetriebsanleitung

2. Connect the water hose to the specific
attachment (Fig.22.A).
3. Lower the cutting height as far as possible.
4. Always stand behind the lawnmower handle.
5. Start the engine.
Paint on internal chassis parts may come off over
time due to the abrasive action of cut grass; if this
happens, promptly touch-up paint with rust-proof paint
to prevent rusting that could corrode the metal.
7.4.3 Cleaning the grass catcher;
1. Empty the grass catcher;
2. Shake it to remove grass cuttings and soil residue;
3. Wash and rinse it, then place it
where it can dry quickly.
7.5

NUTS AND BOLTS

Keep all nuts, bolts and screws tight to be sure
the equipment is in safe working condition.
7.6 BATTERY
The battery is supplied for electric push-button starter
switch models. Read the engine instruction manual
for instructions regarding autonomy, recharging,
reinstating and maintenance of the battery.
7.7

ADJUSTING THE CONVERTER CABLE

This adjustment is necessary when the lever (Fig.23.A)
tends not to remain in the «
IMPORTANT The adjustment must
be made when the engine is off.
With the lever (Fig.23.A) in the «
cable adjuster (Fig.23.B) in the direction indicated by the
arrow as needed to ensure the lever remains in position.
8.

OCCASIONAL MAINTENANCE

Before conducting any inspections, cleaning or
maintenance/adjustment interventions on the machine:
• Stop the machine.
• Make sure that all moving parts have
come to a complete stop.
• Wait until the engine is sufficiently cold.
• Remove the spark plug cap (Fig.24.A).
• Remove the key (Fig.24.C) or battery (for
electric push-button starter switch models).
• Read the relevant instructions.
• Use suitable clothing, protective
gloves and goggles.
8.1

CUTTING MEANS

A badly sharpened cutting means pulls at the
grass and causes the lawn to turn yellow.
» position.
» position, turn the
Do not touch the cutting means until the key has
been removed and the cutting means is completely sta-
tionary.
All work on the cutting means (disassembly, shar-
pening, balancing, repairing, reassembly and/or repla-
cing) are demanding jobs that require special skills as
well as special tools. For safety reasons, these jobs are
best carried out at a Specialised Centre.
Make sure damaged, misshapen or worn cutting-
means are replaced, together with its own screws in
place to preserve balance.
IMPORTANT Always use original cutting means
bearing the code indicated in the "Technical Data".
Given product evolution, the cutting means
listed in the "Technical Data" table may be
replaced in time with others having similar
interchangeable and operating safety features.
9. STORAGE
When the machine is to be stored away:
1. Start the engine in the open air and run it
idle until it comes to a halt, so that it uses up
all the fuel that is left in the carburettor.
2. Wait for the engine to cool.
3. Remove the spark plug cap (Fig.24.A).
4. Remove the key (Fig.24.C) or battery (for
electric push-button starter switch models)
5. Clean the machine thoroughly (par. 7.4).
6. Check the machine for any damage. If necessary,
contact the authorised service centre.
7. Store the machine:
• in a dry place;
• protected from inclement weather;
• covered with a sheet where possible;
• in a place where children cannot get to it.
• making sure that keys or tools used for maintenance
are removed.
9.1

VERTICAL STORAGE

If necessary, some models (see Technical Data
Chart) can be stored vertically (Fig.25.0).
Do not store the machine in a vertical position
with the fuel tank filled above the fuel level indicator
(Fig.21.A).
Proceed as follows:
1. Lower the chassis to the 3rd cutting height (par. 5.7).
2. In the working position, pull both levers
on the handle sides, (Fig.15.B) (Tipo
"I"- "II"), and hold them in position.
3. Fold the handle to the closed position carefully
4. Lift the front part of the machine (Fig.25.0).
EN - 10