Storage - Scheppach BCH5300BP Originalbetriebsanleitung

Clean the air filter Fig. 37 - 40
Soiled air filters reduce the engine power by supply-
ing too little air to the carburetor. Regular checks are
therefore essential.
• Unclip the air filter cover and remove the sponge
filter element.
• To avoid objects falling into the air tank, replace
the air filter cover.
• Wash the filter element in warm soap water, rinse
and allow drying naturally.
Important: Never clean the air filter with petrol or
inflammable solvents.
m Warning!
Never run the engine without the air filter ele-
ment installed.
Lubricate angle transmission
Lubricate with lithium-based grease. Remove the
screw and put in the grease, turning the shaft manu-
ally until grease emerges, then replace the screw.
Adjusting the idle speed Fig. 52
If the cutting device runs idle, correct the idle speed.
1. Allow the engine to warm for 3-5 minutes
(No high speeds!).
2. Turn the adjusting screw (S): clockwise
- idle speed increases (+)
counterclockwise
- Idling speed decreases (-)
The idle speed is 3000 min-1
Contact the manufacturer if the cutter continues to
run at idle.
Do not continue to operate the unit!
Storing the unit
After cutting, clean the unit thoroughly. Store the unit
in a dry room allow the motor to cool down before-
hand.
Important hint in case of sending the equipment
to a service station:
Due to security reasons please see to it that the
equipment is sent back free of oil and gas!
Ordering replacement parts
Please quote the following data when ordering re-
placement parts:
• Type of machine
• Article number of the machine
•
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consumables.
Wear parts*: Line spool, cutting blade, spark plug, air fil-
ter
* Not necessarily included in the scope of delivery!
Replacement parts / accesories:
For the cutting equipment listed here, you can always
use the safety guards provided with the unit.
Grass trimmer/brush cutter:
Spool with Ø 450
Blade with 3 teeth Ø 255 x 1.4
Transport guard for blade 3 teeth
Blade with 4 teeth Ø 255 x 1.5
Transport guard for blade 4 teeth
Blade with 8 teeth Ø 255 x 1.5
Transport guard for blade 8 teeth
Safety shield for grass trimmer

11. Storage

Cleaning
• Keep handles free of oil, so you always have a se-
cure hold.
• Clean the equipment as required with a damp cloth
and, if necessary, mild washing up liquid.
m Important!
• Always pull out the spark boot plug each time be-
fore carrying out any cleaning.
• Never immerse the equipment in water or other liq-
uids in order to clean it.
• Store the chainsaw in a safe and dry place out of
the reach of children.
Storage
Important: Never put the equipment into storage for
longer than 30 days without carrying out the follow-
ing steps.
Storing the equipment
If you intend to store the equipment for longer than 30
days, the equipment must be prepared accordingly.
Otherwise the fuel still remaining in the carburetor will
evaporate and leave a rubbery sediment. This can
cause problems when starting up the equipment and
may require expensive repairs.
1 Slowly remove the fuel tank cap to release any
pressure that may have formed in the tank. Care-
fully empty the tank.
2 To remove the fuel from the carburetor, start the
engine and let it run until the equipment stops.
3 Leave the engine to cool (approx. 5 minutes).
4 Remove the spark plug (see section 10 Change
and clean the spark plug).
5 Add one teaspoon of 2-stroke engine oil into the
combustion chamber. Slowly pull the starter cord
several times to apply a layer of oil to all internal
components. Fit the spark plug again.
Note: Store the equipment in a dry place and far
away from possible ignition sources such as an oven,
a gas-fi red hot water boiler, a gas-fi red dryer, etc.
7910700707
7910700702
3904801065
7910700705
3904801066
7910700711
3904801066
3904803034
GB 31