G Eneral Notes On Safety; U Se Of The Machine For Purposes For Which It Is Intended; I Ncorrect Use; Ec Declaration Of Conformity - SUHNER UBK 6-R Originalbetriebsanleitung

1. n
1.1 g
enerAl notes on sAfety
This operation manual is applicable for the machine UBK
6-R. The machine may only be handled by personnel who
are qualified.
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may con-
tact hidden wiring or its own cord. Contact with a «live»
wire will make exposed metal parts of the tool «live» and
shock the operator.
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
1.2 u
se of the mAchine for PurPoses for
which it is intended
The machine is designed for grinding and polishing of
metal, plastic or wood with abrasive belts, non-woven
belts, high-performance ceramic belts or reinforced non-
woven belts, without using water. The machine is de-
signed exclusively for a 2-hand application.
1.3 i
ncorrect use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 ec
declArAtion of conformity
Otto Suhner GmbH of Trottäcker 50, D-79701 Bad Säck-
ingen, hereby declares under sole responsibility that the
product with the serial or batch no. (see reverse side) com-
plies with the requirements under the Directive 2014/30/
EU, 2006/42/EC, 2011/65/EU. Applied standards: EN ISO
12100, EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-
2, EN 61000-3-3. Document Agent: R Ackermann. D-Bad
Säckingen, 02/2016.
R. Ackermann/Managing Director
2. c
2.1 P

rior to tAKing the mAchine into serVice

Before connecting tool to a power
source, be sure the voltage sup-
plied is the same as specified on
the name plate of the tool. The power sup-
ply should not vary more than 10% above or below the
voltage indicated on the nameplate.
18
S
oteS on afety
ommiSSioning
Check the grinding belt before use. The driver roller must
be installed centrally and aligned to the stop. Under no
circumstances must the grinding belt exceed the max
permitted speed. Observe national regulations. Take pro-
tective measures when dust can develop during working
that is harmful to one's health, cumbustible or explosive.
Wear a dust mask and work with dust/chip extraction
when connectable. Remove safety guard.
Do not use accessories which are not spe-
cifically designed and recommended by the
tool manufacturer. Just because the accessory
can be attached to your power tool, it does not assure safe
operation.
2.2 t

AKing the mAchine into serVice

Preselect speed with adjusting wheel according to speed
table.
Level 1: 14.7 m/s
Level 2: 17.3 m/s
Level 3: 20.5 m/s
Never raise the speed chosen for the belt when it
is running!
2.2.1 t /t
urn on urn off
The switch must be in the OFF position. To turn the ma-
chine on, push the ON/OFF switch toward the front unteil
it clicks in. Press the ON/OFF swith to trigger the blocking
and the machine shuts down.
2.3 r

Ating dAtA

Power voltage
Power Input 230/240V // 120V
Level 4: 23.6 m/s
Level 5: 26.8 m/s
Level 6: 31 m/s
230/240V/120V, 50/60Hz
1530W // 1340W