Caractéristiques Techniques - SUHNER UWC 10 Originalbetriebsanleitung

• ON/OFF switch
Before connecting power cord to receptacle, make sure that
switch 11 is in the Off -0- Position.
Operation conditions and instructions
This tool is equipped with an electronic variable speed tacho-
meter selector and an overload cut-out switch, which operates
as follows:
• Starting current limitaion
Electronically controlled soft starting provides for jerk-free
starting of the machine.
• Temperatur-dependent overload protection
For protection against overheating, when a critical tempera-
ture is reaches the electronic safety function switches to the
cool-down mode.
The machine then continues to run at approx.
2'400 rpm / UWC 10
1'700 rpm / UWC 7
and the elctronic constant-speed control is deactivated.
After a cool-down time of approx. 10-20 s the machine is
again ready for operation. turn the machine OFF and back
ON again to activate the electronic constant-speed control.
With the machine at operating temperature the temperatu-
re-dependent overload protection reacts correspondingly
earlier.
• Undervoltage / restarting protection
On short time power failure (pulled power plug, instable
power supply etc.) the machine will stop. When the power
voltage is restored, the machine has to be turned OFF and
then back ON again. Once this has been done the machine
is again ready for operation.
• Cut-off wheels
When cutting, don't tilt grinder, otherwise it jams.
• Grinding wheels
Best grinding results are achieved if grinder is at a 30 de-
gree angle to the work piece.
Never use a cut-off wheel for grinding.
Do not treat any material containing asbestos.
Caractéristiques techniques
Puissance absorbée
Puissance rendement
Vitesse à vide
Outils ø max.
Niveau pression acoustique
selon EN 60745
Niveau de puissance acoustique 98
K =
Vibration EN 60745
K =
Broche
Poids sans câble env.
Classe de protection
Tension
(voir liste de pièces de rechange)
Avertissement: La valeur de vibration indiquée a été mesurée
selon un processus de contrôle normé et peut diverger de la
valeur en utilisation réelle. Elle peut servir à la comparaison
de différents produits ou à l'estimation préliminaire des temps
d'arrêt.
4
UWC 10 UWC 7
500 500 Watt
300 300 Watt
10'000 7'000 min -1
115 115 mm
87 76 dB(A)
87 dB(A)
3 3 dB(A)
8,1 3,3 m/s 2
2
1,5 1,5 m/s
M14 ou 5/8"-11 M14 ou 5/8"-11
1,7 1,7 kg
II II
diverse diverse
Disconnect Tools
When changing accessories, such as Wheels and discs
• Lock spindle 2 with Lock button 8. Attention: only use lock
button, when machine is at a complete stop.
• Remove or mount flange nut 6 +/or 15
Clean mounting set before installation.
• Check concentricity, use only vibration free tools and always
observe M.O.S. (Max. operating speed).
Maintenance
• Store tool in a clean, dry place.
• Disconnect tool when not in use and before servicing.
• The ventilator openings for cool air must be kept free and
clean, use air gun to blow out dirt.
• Replace grease in grinder head every other time, when
carbon brushes are replaced. Use the SUHNER authorized
service center nearest you .
• Damaged plugs and cords must be replaced immediately.
• Repairs must only be done by a qualified/licensed electri-
cian, otherwise it could be hazardous to the operator.
• Any replacement needed for the connecting line must be
installed by the manufacturer or its agent if safety risks are
to be eliminated.
• Warranty claims can only be considered, if tool is returned
complete.
Accessories
All accessories can be found in the SUHNER Abrasive Power
Tool catalog.
Subject to change!
Eléments de machine
1 Support pour capot de protection
2 Broche
3 Levier d'arrêt
4 Capot de protection
5 Flasque de serrage
6 Ecrou de serrage
7 Clé pour écrou de serrage
8 Bouton d'arrêt pour broche
9 Tête d'angle
10 Poignée
11 Interrupteur
Outils utilisables
12 Disques pour tronçonner et à dégrossir, disques à lamelles
pliées et disques diamantés
13 Support élastique pour disque sur fibre, 14 et écrou de
serrage 15, ou disque à lamelles fixation "Velcro"
16 Outils à visser directement
Pour d'autres outils veuillez consulter le catalogue SUHNER.
FR