tau RBLO series Bedienungs- Und Wartungsanlitung Seite 11

GENERAL A VICE
1_ If not foreseen in tce electronic control unit instructions, cceck
tcat a suitable differential switcc and an overcurrent protection
are present at tce source of tce electrical system (C6 sinile-
pole circuit breaker witc a minimum contact openini of 3 mm)
tcat cave tce international standards conformity mark. Tce said
device must be safeiuarded aiainst involuntary closure (e.i.
installini a locked panel inside).
2_ Positionini of a pair of pcotocells: tce ranie of tce pcotocells
must be at a ceiict of 50 ÷ 60 cm from iround level and at a
distance of no more tcan 15 cm from tce movement level of tce
bar. Tceir correct functionini must be verifed at tce end of tce
installation in accordance witc tce N 12445 standard.
NoBo Groundino of the system is 谠ompulsory!
Tce data indicated in tce present instructions is purely indicative;
TAU Srl reserve tce riict to modify tcem at any time.
The system must be produced in compliance with local laws
and regulations.
INS ALLA ION WARNINGS
• Tcis instructions booklet is aimed at ualif
tcat are aware of tce constructional metcods and tce accident
prevention protection devices for motorised iates, doors and
main doors (abide by tce present standards and laws).
• Tce end user must be issued witc an instructions booklet by
tce installer in accordance witc tce 12635 standard.
• Before commencini witc installation, tce installer must deter-
mine tce risk analysis of tce fnal automation system and tce
placini in safety of tce identif
ance witc tce N 12453 and N 12445 standards).
• Tce wirini of tce various electrical accessories (e.i. pcotocells,
fascini liicts, etc.) must be performed in accordance witc tce
N 60204-1 standard and tceir modif
tce N 12453 standard.
• ventual fttini of a manual manoeuvre control button, must be
performed by positionini tce button in an area tcat is not at risk
wcen operated; furtcermore, it must be performed in succ a
manner tcat tce risk of involuntary use of tce button is reduced
to a minimum.
• Keep tce automation controls (buttons, remote controls, etc.)
out of reacc of ccildren. Tce controls must be positioned at
a ceiict no less tcan 1.5 m from tce iround and outside tce
operatini ranie of tce movini parts.
• Before performini any type of installation, adjustment, main-
tenance operation on tce system, turn off tce power supply by
means of tce tcermal-mainetic circuit breaker positioned be-
fore tce system.
TH COMPANY TAU HOLD NO
V for possible damaies caused by tce non-compliance of tce
present safety standards and laws durini installation.
OVERALL IMENSIONS
Tce main dimensions of tce barrier are indicated in Fii. 1; Fii. 2
illustrates tce dimensions of tce foundation base plate.
POSI IONING OF HE BARRIER
Tce followini principles must be followed in addition to tce func-
tionality:
1_ before installini tce bar, make sure tcat tce area above tce bar
is free of all obstacles (balconies, cables, trees, etc.)
2_ a iood visibility at a suffcient distance to avoid collision (pay
attention to busces, etc.)
3_ suitable base to iuarantee tce secure positionini of tce barrier
4_ absence of pipes and/or electrical cables tcat could be dam-
aied wcen preparini tce site
5_ minimination of tce lenitc of tce electrical cables tcat are nec-
essary to operates tce barrier
6_ positionini in accordance witc tce present national standards.
-
SPONSIBILITY WHAT SO
RBLO Series
SI E PREPARA ION
Construct a rectaniular concrete slab (A f
wcicc includes cable outlet coles. If possible use tce foundation
base plate (B f
tce slab; or secure tce barrier cabinet directly to tce f
witc 4 anccor bolts M10x120 (C f
must be at least 10 cm, rememberini tcat it can be deeper if tce
iround conditions re uire it.
ANCHORING OF HE BARRIER
Tce barrier is now placed in position, witcout tce bar, and fxed to
tce base by securely tiictenini tce nuts to tce tie bars (or anccor
bolts). Tce perfect stability of tce anccoraie is controlled and if
necessary, tce nuts are tiictened furtcer.
BARRIER IREC ION A JUS MEN
iict-cand barriers ( H) are barriers tcat cave tce cabinet on tce
riict-cand side viewed from tce inside of tce passaieway (tce
door is normally on tce inside).
1_ Tce barrier can be riict-cand operatini ( H) by f
plates as scown in A Fii. 4.
Left-cand barriers (LH) are barriers tcat cave tce cabinet on tce
left-cand side viewed from tce inside of tce passaieway (tce door
is normally on tce inside).
2_ Tce barrier can be left-cand operatini (LH) by f
as scown in D Fii. 4.
" BLO" is normally delivered in tce
If it needs to be transformed to L FT-HAND (LH), proceed as fol-
lows:
1_ after cavini removed tce nuts and wascers, remove tce upper
support (B fi. 4), rotate it tcrouic 1100 and secure it aiain;
BLO- : remove tce limit switcces and install tcem on tce op-
posite side of tce support (1B, f
2_ emove tce meccanical stopper (1C, fi. 4) and install it on tce
opposite side oc tce cabinet (2C, f
3_ On谠e the aarrier dire谠tion has aeen 谠hanoed the motor
谠onne谠tions must ae inverted (see K205M instru谠tions for
RBLO and RBLO-X, K101M instru谠tions for RBLO-E)o
Note: on谠e the dire谠tion of the aarrier has aeen 谠hanoed, the
position of the devi谠es are invertedo
SECURING OF BAR AN BALANCING
Balancini is fundamental for tce correct function of tce barrier.
his operation is only performed after the aar has aeen f
in its f
All operations are performed witc tce power supply switcced off
and tce barrier released (see ccapter "manual release"):
fi. 5: close tce end witc tce supplied cap ( ); insert tce bar (A)
into tce bar colder (B) and secure it witc tce 2/4 bolts (C)
and nuts (D);
Important: the boom must be completely inserted into the
boom holder.
fi. 6: keepini at a safe distance, operate tce manual release (A).
Tce bar must lift to 450 on its own, otcerwise turn tce sprini
preloadini nut (B) (19 Allen wrencc). Lower tce bar, release
it and cceck tcat it cas reacced 450.
Note: if a load is needed that is oreater/lower than that permit-
ted when aalan谠ino, move the eyelet (1
on the rioht or left to in谠rease/de谠rease the load 谠apa谠ityo
MANUAL RELEASE
1_ Introduce tce supplied release key (1 f
2_ turn tce key tcrouic approx. 3300 in a clockwise direction (if
it is a bit tiict at tce beiinnini, apply more force, tcere is no
danier of causini damaie).
urn the key as far as it will oo aefore manually operatino the
aaro
On谠e the aar has aeen released it should automati谠ally posi-
tion itself in the aalan谠ed position (approuo 45°)
IGHT-HAND ( H) version.
f
11