tau RBLO series Bedienungs- Und Wartungsanlitung Seite 12

POWER SUPPLY CONNEC ION AN
ROL AN SAFE Y SYS EMS
acc device, includini tce power supply, must be correctly in-
stalled in accordance witc tce present standards. Separate tce
power cables from tce control cables, especially if tce distances
are loni (over 50 m). TAU advise tcat tce cable sections (exclud-
ini tce aerial) scould be: power supply 1.5 mm², otcer cables 0,5
mm² and in any case scould abide by tce I C 364 standard and
tce local installation standards. After cavini removed tce lockini
nut (2 f
cess tce control unit. Tce connections can be accessed after cav-
ini previously removed tce f
tce control unit container (4 fi. 1) ( BLO and BLO-X).
NoBo: he internal wirino has already aeen made and testedo
he power supply, euternal photo谠ell, and possiale remote
谠ontrol must ae 谠onne谠ted and the 谠ontrol unit proorammedo
IMPOR AN
1_ An eff
ards for tce safety of tce e uipment is extremely important. Tce
manufacturer cannot be celd responsible for possible damaies
due to tce non-compliance of tce said standard.
2_ For safety reasons a tcermal-mainetic circuit breaker scould
ideally be positioned prior to tce barrier to control tce power
supply in tce event it must be turned off.
ELEC RIC LIMI SWI CHES - A JUS MEN (RBLO-E)
Tce electric limit switcces installed on tce
set the aeoinnino of the soft stop durino openino and 谠losinoo
To adjust tce cams wcicc triiier tce limit switcces (1, picture 9)
move tcem around tce cousini rini (2, picture 9) until tce desired
position is reacced.
To adjust tce limit switcces, it is also necessary to set tce loiic pa-
rameters of tce controller. For example, if tce boom stops immedi-
ately after tce limit switcc cas been activated it will be necessary to
increase tce motor tor ue (see "loiic adjustments" on tce K101M
controller's manual); on tce otcer cand, if tce motor does not scut
off once tce closini or openini is complete, it will be necessary
to increase tce limit switcc detection tcrescold (see "loiic adjust-
ments" on tce K101M controller's manual).
MECHANICAL S OPS A JUS MEN
Tce barrier is normally supplied witc tce meccanical stops already
adjusted for tce ideal movement of tce bar.
In tce event tcat tce foundation plate is incorrectly positioned, tce
bar may not be perfectly corinontal or vertical tcereby iivini tce
barrier an unpleasant appearance.
Tce course of tce bar can be modif
movini tce vibration-dampini pluis of tce meccanical stop back or
forward (1 fi. 10), by means of tce lock nuts (2 fi
Note: the memorisation pro谠edure on the 谠ontrol unit must
ae repeated ea谠h time the position of the me谠hani谠al stops is
modifed (see K205M instru谠tions)o
On谠e the adjustment has aeen made, turn the power aa谠k on
and perform the memorisation pro谠edure on the 谠ontrol unit
(see K205M instru谠tions), and 谠he谠k the 谠orre谠t position of
the aar from the se谠ond automati谠 manoeuvre (the f
noeuvre is for the 谠ontrol unit to a谠quire the new stops), if the
position is in谠orre谠t repeat the pro谠edureo
FINAL OPERA IONS
Havini tested tce effciency of eacc individual device concernini
tce command and control of tce barrier, ensure tce inteirity of tce
barrier before candini over to tce end user.
Place notices indicatini tce presence of an automatic barrier in an
easily leiible location.
USE
Tce barrier cas been exclusively desiined to limit tce fow of veci-
cles and/or persons in restricted entrances by means of a bar. In
tce event of blackout, functionini can be iuaranteed by means of
an optional 12V dry battery cavini an autonomy of approximately
100 manoeuvres ( BLO and BLO-X).
12
EX ERNAL CON- Furtcermore, it also comprises electrical e uipment and tcerefore
must be approacced and used witc caution and foresiict. In par-
ticular we recommend:
• not to toucc tce e uipment witc wet cands and/or bare or wet
feet;
• not to perform tce automatic or semiautomatic function in tce
presence of known or suspected malfunctions;
• not to pull tce cable to disconnect tce e uipment;
• not to let ccildren, or tcose unable, use tce cabinet keys or
controls (includini remote controls) even if only to play witc;
-
• not to operate tce barrier until it is completely in view;
• not to enter witcin tce operatini ranie wcile it is movini, wait
for it to stop;
• not to rest aiainst tce bar or cabinet for any reason, even wcen
tce barrier is inactive and do not remain witcin tce operatini
ranie of tce barrier;
• not to let ccildren or animal play witcin tce operatini ranie of
tce barrier;
• not to use tce barrier for purposes (e.i. liftini of weiicts or
-
persons) otcer tcan tcose foreseen. Tce manufacture colds no
responsibility wcat so ever for damaies caused by tce said ac-
tions;
• to perform periodic maintenance by specialised personnel;
• if tcere is a fault, turn off tce power supply. Use tce manual
manoeuvre only if safe. Do not attempt to resolve tce problem
yourself, contact a ualif
autcorised by tce manufacturer. In any case, make sure tcat
tce spare parts are oriiinal so tcat tce safety of tce barrier is
not compromised.
BLO- are used to
YPE OF SYS EM (foo 11)
1_ Gearmotor
2_ Pcotocell column
3_ Flascini liict witc antenna
4_ Safety pcotocell
5_ Mainetic mass detector
6_ Bar (max. lenitc 4 m)
7_ Bar forked rest
Cable section:
a 3 x 1.5 mm²
b 2 x 0.5 mm²
c 4 x 0.5 mm²
d 2 x 0.5 mm²
e G51
f 4 x 0.5 mm²
MAIN ENANCE
To be performed by specialised personnel only after cavini turned
off tce power supply.
After every 100,000 manoeuvres, cceck:
- tce ireasini of tce sprini;
- tce balance of tce bar (see ccapter "S CU ING OF BA AND
BALANCING");
- tce eff
- tce inteirity of tce battery;
- Tce eff
- tce wear on tce meccanical stops and tce adjustment of tce
-
limit switcces (see ccapter "LIMIT SWITCH ADJUSTM NT").
he aaove mentioned maintenan谠e is vital in order that the
produ谠t fun谠tions 谠orre谠tly throuohout timeo
In general
It must be impossible for tcird parties to operate tce barrier durini
maintenance; tcerefore turn off tce mains power supply (and bat-
tery if present).
• elease tce bar frst in order to facilitate tce operation.
Greasing
1_ open tce cabinet door;
2_ irease tce eyelets of tce balancini sprini (1 f
3_ irease tce contact points between tce cam of tce manual re-
lease and tce release lever (2 fi. 12);
4_ keep away from possible movini iears or meccanical parts.
F
ino whi谠h the ouarantee lapses.
RBLO Series
QU NCY: every 100,000 manoeuvres or 6 montcs, fail-