Herunterladen Diese Seite drucken

Operation; Transport; Storage; Care And Service - Kärcher T 9/1 Bp Originalbetriebsanleitung

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
Inserting the battery pack
1. Slide the battery pack into the battery holder and
lock it in place.
Charging the battery pack
Note
Please read the operating instructions of the charger
manufacturer, especially the chapters on safety instruc-
tions!
Note
Please read the operating instructions of the battery
pack manufacturer, especially the chapters on safety in-
structions!
Note
The battery pack is partially charged on delivery.
Charge before use and when necessary.
Note
The battery pack can only be charged when it is re-
moved.
1. Press the unlocking button and remove the battery
pack.
2. Charge the battery pack according to the operating
instructions of the charger manufacturer and the
battery pack manufacturer.

Operation

Switch on the device
1. Switch on the device at the main switch.
Eco-Mode
Eco button (energy-saving mode): The device works
with reduced suction performance. The battery run time
is extended.
1. To activate Eco-mode: Actuate the Eco switch. The
indicator light in the switch lights up green.
2. To switch off Eco-mode: Actuate the Eco switch re-
peatedly. The indicator light in the switch goes out.
Adjusting the suction power
1. Regulate the suction power on the suction control.
Cleaning mode
Note
During the basic cleaning of textile coats, the battery run
time is shortened due to increased cleaning performance.
1. Set the floor nozzle switch to hard surface or carpet.
2. Perform cleaning.
Switching off the device
1. Switch off the device at the main switch.
Each time after use
1. Empty the container.
2. Vacuum off the inside and outside of the device and
clean with a moist cloth.
Storing the device
1. Store the device in a dry room and secure it against
unauthorised use.

Transport

CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
1. When transporting the device in vehicles, secure it
to prevent it from slipping or overturning in accord-
ance with the respective valid guidelines.
8
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
The device may only be stored indoors.
1. Press the unlocking button and remove the battery
pack to prevent discharge.

Care and service

DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the battery pack.
Cleaning the main filter basket
ATTENTION
Danger from wet main filter basket
Risk of damage to the device
Never insert the main filter basket when wet.
1. If necessary, clean the main filter basket (washable)
under running water.
Replacing the motor protection filter
1. Unlock and remove the suction head.
2. Remove the motor protection filter.
3. Fit the new motor protection filter.
4. Fit and lock the suction head.

Troubleshooting guide

DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the battery pack.
The device stops during operation
The motor thermo-protector has triggered
1. Change the fleece filter bag or paper filter bag (spe-
cial accessories).
2. Replace the motor protection filter.
3. Check all parts for clogging.
4. Switch on the device.
Suction power decreases
1. Remove any blockages from the suction nozzle,
suction pipe or suction hose.
2. Change the fleece filter bag or paper filter bag (spe-
cial accessories).
3. Clean the main filter basket under running water and
dry.
4. Position/lock the suction head correctly.
5. Replace the defective suction hose.
6. Replace the motor protection filter.
Escaping dust when vacuuming
1. Change the fleece filter bag or paper filter bag (spe-
cial accessories).
2. Check the fleece filter bag or paper filter bag (spe-
cial accessories) is fitted correctly.
3. Position/lock the suction head correctly.
4. Insert the undamaged main filter basket.
5. Insert the motor protection filter correctly.
Device not running
1. Switch on the device.
2. Allow the overheated board to cool down.
3. Charge the battery pack.
4. Insert the battery pack.
English

Storage

Werbung

Fehlerbehebung

loading