Ec Declaration Of Conformity; Instruction Manual; General Power Tool Safety Warnings - Makita GA7060 Betriebsanleitung

W ork mo d e : d is c san d ing w it h normal si d e grip
Vibration emission (a
h , D S
Uncertainty (K) : . m/s
Work mode: disc sanding with anti vibration side grip
Vibration emission (a
h , D S
Uncertainty (K) : . m/s
Model GA9060R
Work mode: surface grinding with normal side grip
Vibration emission (a
h , A G
Uncertainty (K) : . m/s
Work mode: surface grinding with anti vibration side grip
Vibration emission (a
h , A G
Uncertainty (K) : . m/s
W ork mo d e : d is c san d ing w it h normal si d e grip
Vibration emission (a
h , D S
Uncertainty (K) : . m/s
Work mode: disc sanding with anti vibration side grip
Vibration emission (a
h , D S
Uncertainty (K) : . m/s
NOTE: The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
anot h er.
NOTE: The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
The vibration emission during actual
WARNING:
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
Be sure to identify safety measures
WARNING:
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
t h e times w h en t h e tool is s w it c h e d o f f an d w h en it is
running idle in addition to the trigger time).
The declared vibration emission
WARNING:
value is used for main applications of the power tool.
However if the power tool is used for other applica-
tions, the vibration emission value may be different.

EC Declaration of Conformity

For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
General pow er tool safety w arnings
WARNING:
Read all safety w arnings and
all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all w arnings and instruc-
tions for future reference.
The term power tool in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
) : . m/s
2
or less
2
) : . m/s
2
or less
2
) : . m/s
2
2
) : . m/s
2
2
) : . m/s
2
or less
2
) : . m/s
2
or less
2
Grinder safety w arnings
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1 . This pow er tool is intended to function as a
grinder, sander, w ire brush or cut-off tool. Read
all safety w arnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
2. Operations such as polishing are not recom-
mended to be performed w ith this pow er tool.
O perations f or w h ic h th e pow er tool w as not d esigned
may create a hazard and cause personal injury.
Do not use accessories which are not specifically
3.
designed and recommended by the tool manufac-
turer. ust because the accessory can be attached to
your power tool, it does not assure safe operation.
4 . The rated speed of the accessory must be at
least equal to the maximum speed marked on
the po w er tool. Accessories running faster than
their rated speed can break and fly apart.
5 . The outside diameter and the thickness of your
accessory must be w ithin the capacity rating
of your po w er tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
6 . Threaded mounting of accessories must match
the grinder spindle thread. For accessories
mounted by anges, the arbour hole of the
accessory must fit the locating diameter of the
ange. Accessories that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
7. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive w heels for
chips and cracks, backing pad for cracks, tear or
excess w ear, w ire brush for loose or cracked w ires.
If po w er tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders a w ay from the plane of the
rotating accessory and run the po w er tool at maxi-
mum no-load speed for one minute. D amage d a c c es-
sories will normally break apart during this test time.
8 . Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, w ear dust mask,
hearing protectors, gloves and w orkshop apron
capable of stopping small abrasive or w orkpiece
fragments. The eye protection must be capable of
stopping flying debris generated by various operations.
The dust mask or respirator must be capable of filtrating
particles generated by your operation. Prolonged expo-
sure to high intensity noise may cause hearing loss.
.
Keep bystanders a safe distance aw ay from w ork
area. Anyone entering the w ork area must w ear
personal protective equipment. F ragments of
workpiece or of a broken accessory may fly away and
cause injury beyond immediate area of operation.
1 0. Hold the pow er tool by insulated gripping sur-
faces only, w hen performing an operation w here
the cutting accessory may contact hidden w iring
or its ow n cord. Cutting accessory contacting a live
wire may make exposed metal parts of the power tool
live and could give the operator an electric shock.
7 ENGLISH