Makita GA7060 Betriebsanleitung Seite 10

For tool w ith the lock-on and lock-off s w itch
CAUTION:
S w itch can be locked in " ON " posi-
tion for ease of operator comfort during extended
use. Apply caution w hen locking tool in " ON "
position and maintain firm grasp on tool.
To prevent the switch trigger from accidentally pulled, a
lo c k le v er is pro v i d e d .
To start the tool, push in the lock lever (in the A direc-
tion) and then pull the switch trigger (in the B direction).
R elease t h e s w it c h trigger to stop.
For continuous operation, push in the lock lever (in the
A direction), pull the switch trigger (in the B direction)
and then pull the lock lever (in the C direction).
To stop the tool from the locked position, pull the switch
trigger fully (in the B direction), then release it.
NOTICE:
Do not pull the s w itch trigger hard
w ithout pressing in the lock-off button. T h is c an
cause switch breakage.
Indication lamp
Only for model GA7060R / GA9060R
Fig.3: 1. I n d i c ation lamp
The indication lamp lights up green when the tool is plugged.
If the indication lamp does not light up, the mains cord
or the controller may be defective.
The indication lamp is lit but the tool does not start even
if the tool is switched on, the carbon brushes may be
worn out, or the controller, the motor or the ON/OFF
switch may be defective.
Unintentional restart proof
The tool does not start with the switch being lock-on
even when the tool is plugged.
At this time, the indication lamp flickers red and shows
the unintentional restart proof device is on function.
To cancel the unintentional restart proof, return the
po w er s w it c h to O F F position.
NOTE: Wait more than one second before restarting
the tool when unintentional restart proof functions.
Soft start feature
Soft start feature reduces starting reaction.
ASSEMBLY
CAUTION:
Al w ays be sure that the tool is
s w itched off and unplugged before carrying out
any w ork on the tool.
Installing side grip (handle)
CAUTION:
Al w ays be sure that the side grip is
installed securely before operation.
Screw the side grip securely on the position of the tool
as shown in the figure.
Fig.4
Installing or removing w heel guard
(For depressed center wheel, ap disc,
ex wheel, wire wheel brush / abrasive
cut-off w heel, diamond w heel)
WARNING:
wheel, ap disc, ex wheel or wire wheel brush,
the wheel guard must be fitted on the tool so that
the closed side of the guard al w ays points to w ard
the operator.
WARNING:
/ diamond wheel, be sure to use only the special
w heel guard designed for use w ith cut-off w heels.
(In some European countries, when using a diamond
wheel, the ordinary guard can be used. Follow the
regulations in your country.)
For tool w ith locking screw type
w heel guard
Mount the wheel guard with the protrusions on the
wheel guard band aligned with the notches on the bear-
ing box. Then rotate the wheel guard to such an angle
that it can protect the operator according to work. Be
sure to tighten the screw securely.
To remove wheel guard, follow the installation proce-
dure in reverse.
Fig.5: 1. Wheel guard 2. Bearing box 3. S c re w
For tool w ith clamp lever type w heel guard
Loosen the screw, and then pull the lever in the direc-
tion of the arrow. Mount the wheel guard with the protru-
sions on the wheel guard band aligned with the notches
on the bearing box. Then rotate the wheel guard to such
an angle t h at it c an prote c t t h e operator a c c or d ing to
w ork.
Fig.6: 1. Wheel guard 2. Bearing box 3. S c re w
4. Lever
Pull the lever in direction of the arrow. Then tighten the
wheel guard with fastening the screw. Be sure to tighten
the screw securely. The setting angle of the wheel
guard can be adjusted with the lever.
Fig.7: 1. S c re w 2. Lever
To remove wheel guard, follow the installation proce-
dure in reverse.
Installing or removing depressed
center wheel or ap disc
Optional accessory
WARNING:
wheel or ap disc, the wheel guard must be fitted
on the tool so that the closed side of the guard
al w ays points to w ard the operator.
CAUTION:
Make sure that the mounting part
of the inner ange fits into the inner diameter of
the depressed center wheel / ap disc perfectly.
Mounting the inner flange on the wrong side may
result in the dangerous vibration.
10 ENGLISH
When using a depressed center
When using an abrasive cut-off
When using a depressed center