Error Messages; Cleaning And Disinfecting; Battery Replacement; Technical Specifications - Microlife NC 200 Bedienungsanleitung

 Reading 1 - the last reading AQ: Press and release the M-
button 5 to recall the last reading. Number «1» and a flashing
«M» are displayed.
Pressing and releasing the M-button 5 after the last 30 readings
have been recalled will resume the above sequence from reading 1.

10. Error Messages

 Measured temperature too high AR: Displays «H» when
measured temperature is higher than 43 °C / 109.7 °F in body
mode or 100 °C / 212 °F in object mode.
 Measured temperature too low AS: Displays «L» when
measured temperature is lower than 34.0 °C / 93.2 °F in body
mode or 0 °C / 32 °F in object mode.
 Ambient temperature too high BT: Displays «AH» when
ambient temperature is higher than 40.0 °C / 104.0 °F.
 Ambient temperature too low BK: Displays «AL» and
when ambient temperature is lower than 15.0 °C / 59.0 °F in
body mode or lower than 5.0 °C / 41.0 °F in object mode.
 Error function display BL:
- «Er 0» / «Er 6»: The system has a malfunction.
- «Er 2»: Device is directly placed on the forehead / object.
Keep the measuring distance of 1-5 cm. Do not touch the
bottom side (sensing area) of the measuring sensor.
 Blank display BM: Check if the batteries have been inserted
correctly. Also check polarity (<+> and <->) of the batteries.
 Flat battery indicator BN: If only «battery» icon is shown on
the display, the batteries should be replaced immediately.

11. Cleaning and Disinfecting

Use an alcohol swab or cotton tissue moistened with alcohol (70%
Isopropyl) to clean the thermometer casing and the measuring
sensor. Ensure that no liquid enters the interior of the device. Never
use abrasive cleaning agents, thinners or benzene for cleaning and
never immerse the device in water or other cleaning liquids. Take
care not to scratch the surface of the sensor lens and the display.

12. Battery Replacement

This device is supplied with 2 new, long-life 1.5V, size AAA
batteries. Batteries need replacing when this icon «battery» BN is
the only symbol shown on the display.
Remove the battery cover BQ by sliding it in the direction shown.
Replace the batteries – ensure correct polarity as shown by the
symbols in the compartment.
6
Batteries and electronic devices must be disposed of in
accordance with the locally applicable regulations, not with
domestic waste.
13. Guarantee
This device is covered by a 5 year guarantee from the date of
purchase. The guarantee is valid only on presentation of the guar-
antee card completed by the dealer (see back) confirming date of
purchase or the receipt.
 The guarantee covers the device. Batteries and packaging are
not included.
 Opening or altering the device invalidates the guarantee.
 The guarantee does not cover damage caused by improper
handling, discharged batteries, accidents or non-compliance
with the operating instructions.
Please contact Microlife-service.

14. Technical Specifications

Type: Non Contact Thermometer NC 200
Measurement Body mode: 34.0 - 43 °C / 93.2 - 109.4 °F
range: Object mode: 0 - 100.0 °C / 32 - 212.0 °F
Resolution: 0.1 °C / °F
Measurement Body mode:
±0.2 °C, 35.0  42.0 °C / ±0.4 °F, 95.0  107.6 °F
accuracy
±0.3 °C, 34.0  34.9 °C and 42.1 43.0 °C /
(Laboratory):
±0.5 °F, 93.2 94.8 °F and 107.8 109.4 °F
Object mode:
±1.0 °C, 0 100.0 °C / ±2 °F, 32.0 212 °F
Display: Liquid Crystal Display, 4 digits plus special icons
Acoustic:
The unit is turned ON and ready for the measure-
ment: 1 short beep.
Complete the measurement: 1 long beep (1 sec.) if
the reading is less than 37.5 °C / 99.5 °F, 10 short
«beep» sounds, if the reading is equal to or greater
than 37.5 °C / 99.5 °F.
System error or malfunction: 3 short «bi» sounds.
Memory: 30 readings recall in the memory mode with a
record of both time and date.