Measuring In Object Mode Without Auto Measurement; Changing Between Celsius And Fahrenheit; How To Recall 30 Readings In Memory Mode - Microlife NC 200 Bedienungsanleitung

5. The device will start the measurement automatically, when
the measuring sensor 1 detects the distance is appropriate
within 5 cm. The display will show a countdown (3, 2, 1); after
3 seconds a long beep will verify the completion of measurement.
6. Self-measurement: The green self-indicator light 3 will help
to distinguish the start of the measurement. Keep the thermom-
eter pointed towards the forehead until the light switches off.
7. Read the recorded temperature from the LCD display.
8. For the next measurement remove the thermometer from the
forehead and wait until the «°C»/«°F» icon is flashing. Follow
steps 4-5 above.
9. Press and hold the START/IO button 7 for 3 seconds to turn
off the device; otherwise the device will automatically switch off
after approx. 60 seconds.

Measuring in object mode without auto measurement

1. Press the START/IO button 7. The display 4 is activated to
show all segments for 1 second.
2. Press the MODE button 6 to switch to object mode.
3. A flashing «°C»/«°F» icon, the blinking blue tracking light 2 and
a beep indicate that the device is ready for measurement AT.
4. Aim the thermometer at the center of the object you want to
measure with a distance of no more than 5 cm. Press the
START/IO button 7. After 3 seconds a long beep will verify
the completion of measurement.
5. Read the recorded temperature from the LCD display.
6. For the next measurement wait until the «°C»/«°F» icon is
flashing and follow steps 4-5 above.
7. Press and hold the START/IO button 7 for 3 seconds to turn
off the device; otherwise the device will automatically switch off
after approx. 60 seconds.

NOTE:
 Patients and thermometer should stay in similar room
condition for at least 30 minutes.
 Don't take a measurement while or immediately after nursing a
baby.
 Don't use the thermometer in high humidity environments.
 Patients should not drink, eat or exercise before/while taking
the measurement.
 Don't move the measurement device from the measuring area
before hearing the termination beep.
 10 short beeps and a red LCD backlight alert the patient that he/
she may have a temperature equal to or higher than 37.5 °C.
NC 200
 Always take the temperature in the same location, since
temperature readings may vary according to locations.
 Doctors recommend rectal measurement for newborn infants
within the first 6 months, as all other measuring methods might
lead to ambiguous results. If using a non contact thermometer
on those infants, we always recommend verifying the readings
with a rectal measurement.
 In the following situations it is recommended that three temper-
atures are taken with the highest one taken as the reading:
1. Children under three years of age with a compromised
immune system and for whom the presence or absence of
fever is critical.
2. When the user is learning how to use the thermometer for
the first time until he/she has familiarized himself/herself with
the device and obtains consistent readings.
3. If the measurement is surprisingly low.
 Readings from different measuring sites should not be
compared as the normal body temperature varies by
measuring site and time of day, being highest in the evening
and lowest about one hour before waking up.
Normal body temperature ranges:
- Axillar: 34.7 - 37.3 °C / 94.5 - 99.1 °F
- Oral: 35.5 - 37.5 °C / 95.9 - 99.5 °F
- Rectal: 36.6 - 38.0 °C / 97.9 - 100.4 °F
- Microlife NC 200: 35.4 - 37.4 °C / 95.7 - 99.3 °F

8. Changing between Celsius and Fahrenheit

This thermometer can display temperature readings in either Fahr-
enheit or Celsius. To switch the display between °C and °F, press
and hold the MODE button 6 for 3 seconds; the beeper icon is
shown on the display. Press the MODE button again; the current
measurement scale («°C» or «°F» icon) will be shown on the
display AO. Change the measurement scale between °C and °F by
pressing the M-button 5. When the measurement scale has been
chosen, press the START/IO button 7 to enter the «ready for
measuring» mode; otherwise the device automatically switches to
ready for measuring after 10 seconds AT.

9. How to recall 30 readings in Memory Mode

This thermometer can recall the last 30 readings with a record of
both time and date.
 Recall mode AP: Press the M-button 5 to enter recall mode
when the power is off. The memory icon «M» will flash.
EN
5