Declaration Of Installation Conformity; Section 4 Paragraph 1 - Elektror ND series Betriebs- Und Montageanleitung

www.elektror.com
8 DECLARATION OF INSTALLATION CONFORMITY PURSUANT TO ANNEX II 1 B
DECLARATION OF CONFORMITY IN ACC. WITH EVPG (ENERGY CONSUMPTION
RELEVANT PRODUCTS ACT) SECTION 4 PARAGRAPH 1
The manufacturer,
Elektror airsystems gmbh
Hellmuth-Hirth-Strasse 2
D-73760 Ostfi ldern
hereby declares that the product to which this declaration refers meets the basic requirements of the Machinery Directive
(2006/42/EC) as set forth below.
Description of incomplete machine:
Low pressure blower D 03 M, E 03, D 04 M, E 04, D 045 M, E 045, D 05 M, E 05, D 052 M, E 052, D 060, E 060, D 064, E
064, D 066, E 066, D 07, D 072, D 08, D 082, D 09, D 092, 2D 04, 2D 045, 2D 05, 2D 052, 2D 060, 2D 064, 2D 066, 2D 07,
2D 08
Serial number and year of manufacture can be found on the rating plate and on the accompanying delivery slip.
Description of the essential requirements of Machinery Directive (2006/42/EC), with which the partially completed
machine complies:
Machinery Directive (2006/42/EC): Annex I, Articles 1.1.2, 1.1.3, 1.1.5, 1.3.2, 1.3.3, 1.3.4, 1.3.7, 1.5.1, 1.6.1, 1.7.1, 1.7.3
Electromagnetic Compatibility Directive (2014/30/EU).
The partially completed machine described here continues to fulfi l the protective regulations of the Low Voltage Directive
(2014/35/EC) according to Annex I, No. 1.5.1 of the Machinery Directive.
The commissioning of the partially completed machine is not permitted until it has been verifi ed that the machine in which
the partially completed machine is to be installed, complies with the provisions of the Machinery Directive (2006/42/EC).
The product also meets the requirements of the guideline for the sustainable design of energy consumption relevant prod-
ucts (2009/125/EC) and the implementing regulations VO 640/ 2009 for electric motors and VO 327/ 2011 for fans.
The following harmonised standards were applied:
DIN EN ISO 12100 2011 Safety of machinery - General principles of design -
Risk assessment and risk reduction
ISO 14694 2010 Industrial fans - technical specifi cations for balancing quality and vibration level
DIN EN 60034-1 2011 Rotating electrical machines,
Part 1: Rating and performance
DIN EN 60034-5 2007 Rotating electrical machines,
Part 5: Degrees of protection provided by the integral
design of rotating electrical machines (IP code) – Classifi cation
DIN EN 60034-30-1 2014 Rotating electrical machines - Part 30: Effi ciency classes of single-speed, three-phase,
cage-induction motors (IE code)
DIN EN 60204-1 2019 Safety of machinery – Electrical equipment of machines,
Part 1: General requirements
DIN EN 60664-1 2008 Insulation coordination for equipment within low-voltage systems,
Part 1: Principles, requirements and tests
The manufacturer, Elektror airsystems gmbh, undertakes to make the special documentation on this incomplete machine
available, electronically or in hardcopy, to national authorities on demand. The special technical documentation belonging to
this incomplete machine was prepared in accordance with Annex VII Part B.
Mr Kevin Kargar, tel. +49 711 31973-1179, is responsible for the documentation.
Kreher (Managing Director)
Ostfi ldern, 17.01.20
Operating and assembly instructions ND
EN
17