Maintenance - Chicco STYLEGO Bedienungsanleitung

long time.
• Before lifting or transporting the
carrycot, the base needs to be ad-
justed to the lowest position.
• Head of the child in the carry cot
should never be lower than the
body of the child.
• The child restraint system must be
covered when the product is used
outside the car.
CLEANING AND MAINTENANCE
This product requires periodical maintenance. Cleaning and
maintenance operations must be performed exclusively by
an adult.
CLEANING
Clean the fabric parts using a wet sponge and neutral soap.
Periodically wipe clean plastic parts with a soft damp cloth.
Always dry the metal parts to prevent the formation of rust
if the stroller has come into contact with water.
WASHING
The external/internal lining of the carrycot and the mattress
are removable and washable; in order to remove them, please
refer to the paragraph REMOVING THE CARRY COT LINING.
it is advised to carefully follow the washing instructions
shown on the item's label.
Below are the cleaning symbols and their meanings:
Wash by hand in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean

MAINTENANCE

Always let the metal parts dry to prevent the formation
of rust. Do not submerge the carry cot in water. Routinely
wipe clean plastic parts with a soft damp cloth. To avoid
friction, ensure that the locking devices of the carry cot and
stroller are free from dust or sand. Do not leave the product
exposed to the sun for a long period of time; the fabrics
may discolour. Lubricate the moving parts only if necessary,
with a light application of a silicone based lubricant.
CARRY COT FEATURES
The carrycot is comprehensive of the following components:
fabric lining, hood, cover, mattress, comfort kit (two shoulder
straps and a crotch strap), and kit for car transportation.
1. The carry cot is supplied with the fabric lining already fit-
ted (fig. 1) (except for hood and cover).
HOOD
The carry cot is equipped with a sun canopy and wind-
shield that can be adjusted to various positions.
ATTACH AND REMOVE
2. To mount the hood on the carry cot, position the pin
joints found on both sides of the carry out vertically (fig.
2A), and insert the two plastic ends in the slots as illus-
trated in fig. 2B.
3. To complete the mounting of the fabric part of the hood,
fasten the two click buttons located on both sides of the
carry cot (fig. 3).
4. Then pass the metal pin through the fabric slot located
inside the back of the hood (fig. 4).
REAR OPENING
5. To ensure proper ventilation, the carry cot features a rear
opening; to open it, just fold the flap on the upper part of
the carry cot (fig. 5).
VISOR
6. The internal part of the visor features a fabric ring that al-
lows you to hang soft toys (fig. 6).
COVER
7. To fasten the cover close both the zips by your child's
feet (Fig. 7). Then fasten the fabric flap of the cover to the
hood using the two snap buttons (fig. 7A). To ensure the
utmost safety of your child, you can use the fabric flap in
the vertical position, fastening it using the relevant holes
(fig. 7B).
COMFORT KIT
The Comfort Kit features 2 shoulder pads and crotch strap.
8. To put on the comfort kit, insert the shoulder pads on the
straps as shown in fig. 8A and fit the crotch strap inside
the padding (fig. 8B).
ADJUSTABLE BACKREST - COMFORT SYSTEM
9. carrycot's backrest can be adjusted gradually. To incline
or recline the backrest, use the wheel located on the
outer part of the carry cot near the baby's feet (fig. 9).
CARRYING HANDLE
10. The carrycot features a comfortable carry handle that
can be adjusted in three positions (fig. 10):
A) Transport
B) Middle
C) Rest
11. To put the handle in the vertical position, grasp it in the
centre and pull it up until you hear a click (fig. 11 A);
to put the handle back in the rest position, press both
buttons at the base of the handle at the same time and
then turn it downwards (fig. 11B - 11C).
WARNING: Do not transport the carrycot with the handle
in middle or rest position, but only with the handle in carry-
ing position (vertical).
REMOVING THE CARRY COT LINING
Before starting to remove the carry cot lining, unfasten the
safety harness (see the paragraph USING THE CARRY COT
SAFETY HARNESS) and remove the comfort kit.
12. To remove the hood, unfasten the buttons on the sides
and pull out the fabric from the pin in the rear part of
14
13
RE
14
CA
Th
po
WA
tra
15
16
US
17
18
19
WA
bu
WA
co
20
WA
dle
US
Re
ing
ou
• K
• F