Brief Description; Working Instructions - Felisatti AG115/1000S Bedienungsanleitung

Read the operating instructions
Protection category II power tool; double
insulated
In accordance with essential applicable safety
standards of European directives
Wear eye protection
Follow very carefully the instructions in this manual,
save it and keep it close at hand, ready to carry out any
inspection of parts that may be necessary.
If the tool is used with care and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have bought
shall be only those described in this manual. Any other
use of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
1 Start-up switch (Fig.1)
2 Auxiliary handle (Fig.1)
3 Disc guard for sanding operation (Fig.1)
4 Disc guard for cutting-off operations (Fig.1)
5 Spindle (shaft) (Fig.1)
6 Spindle blocking button (Fig.1)
7 Support plate (Fig.1)
8 Abrasive disc (Fig.1)
9 Clamping nut (Fig.1)
10 Pin spanner (Fig.1)
11 Clamping plate (Fig.1)
12 Screw (Fig.1)
13 Screw (Fig.1)
EQUIPMENT
- Disc guard (for sanding operation)
- 1 auxiliary handle
- 1 pin spanner
- Disc clamping nuts
- Operating instructions with Safety instructions
- Warranty

BRIEF DESCRIPTION

This angle grinder has been designed for cutting,
deburring and cutting metals and stone without the use of
water.
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage
is correct: it must be the same as that on the specification
label. Machines with 230V can also be connected to a
220V mains supply.
FITTING SAFETY DEVICES
WARNING! Always unplug the machine before
carrying out work on it.
1. Fitting the disc guard
To change the disc guard unscrew 4 screws 12 and 13
from clamping plate of guard 11, take off the guard, place
another guard, place the clamping plate matching holes of
the guard and of the clamping plate, tight screws.
The guard can be rotated around the spindle. For this:
- loosen the screw 13 of the guard;
- rotate the guard in the position excluding spark
emission in direction of operator;
tight the screw 13.
-
WARNING! The closed part of the disc guard should
always point towards the user.
2. Fitting the auxiliary handle 2
Use of the auxiliary handle is obligatory in order to
ensure greater control and safety when handling the tool.
The auxiliary handle 2 must be screwed on to the right or
left side, depending on the type of work to be carried out.
FITTING THE ACCESSORIES (DISCS AND WHEELS)
WARNING! For safety reasons, the machine should
always be unplugged from the mains before changing the
disc or wheel. Always work with the guard on and wear
safety goggles.
Use deburring and cutting discs with fibre-reinforced
synthetic binders, for a max. peripheral speed of 80 m/s
and cup wheels with synthetic binder for 45 m/s. Protect
discs and wheels from knocks and blows.
WARNING! Never press the blocking button when
the machine is running. The shaft must have stopped com-
pletely before the blocking button is pressed. To fit the disc,
proceed as follows:
1. Block the spindle (shaft) 5, by pressing the blocking
button 6.
With the pin spanner 10, remove the clamping nut 9
2.
from the spindle 5.
Fit the abrasive disc on the support plate 7.
3.
4. Replace the clamping nut 9, using the pin spanner 10.
The position of the nut 9 will depend on the thickness of the
disc
5. Once the disc is fitted, check that the blocking button
has returned to its original position due to movement of the
incorporated spring.
STARTING THE TOOL
WARNING! Check that the mains voltage is the same
as that in the machine's specifications.
Plug the machine in with the switch off. Start the
machine by turning the switch to position 1 ("ON"). To
switch off, do the same in reverse.

WORKING INSTRUCTIONS

For cutting or deburring, the part to be worked on must
be secured, unless it is heavy enough to remain in a stable
position by itself.
For optimum performance and results when deburring,
it is advisable that the surface and the disc form an angle
of approximately 30º-40º. Guide the tool by pressing
lightly forwards and backwards. This prevents the part
from overheating or changing colour and the formation of
striations.
WARNING! Never use a cutting disc for deburring.
When cutting, do not exert pressure on the disc. Do not
tilt the machine. The disc should not tilt or oscillate. Work
with a steady speed, appropriate for the type of material.
When cutting, bear in mind the direction of the work.
Guide the machine against the direction of the cutting tool,
never in the opposite direction; otherwise there is a risk
of the machine veering off the cutting line uncontrollably.
When cutting profiles or rectangular section tubes, we
recommend starting the cut on the shortest side.
7