Installation; Electrical Connection; Cleaning And Maintenance - Litecraft battled AT10.x Bedienungsanleitung

Installation

• There are specific regulations like BGV C1 (old VBG 70) or
country related regulations which need to attend during
the installation. The installation has to be handled by skilled
persons only!
• Suspension device hast to be built and calculated in order to
handle up to 10 times its specific load limit over a time of
one hour without permanent or harmful deformation.
• Installation has to be done with a separate, independent
suspension device like a safety chain. A second suspension
device has to be built in order to assure that in case of error
no part of an installation can fall off.
• Trepassing the danger zone below the installation during the
assembling is prohibited.
• Installer has to take care of all safety and machinery instal­
lations are approved by authorized persons before first opera­
tion or after changes before restarting.
• Installer has to take care of all safety and machinery installa­
tions are approved by skilled persons at least once a year.
• Installer has to take care of all safety and machinery installa­
tions are approved by authorized persons at least every four
years during the acceptance inspection.
• Spotlight should ideally installed outside peoples lounge area.
ATTENTION!
Installation overhead needs a high level of experience. This
includes (but is not just limited to) calculation and definition
of load capacity, used installation material and regular safety
inspections of used material and the fixture itself. Never
try to do the installation by yourself if you are not qualified,
instead you have to instruct a skilled installer. Inappropriate
installations can cause injuries and/or damage of property.
• Spotlight has to be installed outside areas where people can
touch it.
• Professional truss system or similar licensed suspension sys­
tems have to be used if the spotlight is used in suspension
from ceiling or other constructions. Spotlights can never be
installed freely suspended!
ATTENTION!
Spotlights can cause injuries when fall off. If you are not trai-
ned in questions of safety for the different kinds of installation
do NOT install the spotlight!
• Assure that the mounting surface can hold at least ten times
the point load of the spotlight before installing the fixture.
ATTENTION!
Assure the specified safety distances to flammable material.
• Attach the spotlight with its yoke and the use of a suitable
hook/clamp to your truss system. The therefor used opening
has a diameter of about 12 mm. According to your installa­
tion also similar but approved suspension devices are possible.
• When installing the spotlight overhead make sure to safe the
fixture by a safety chain which is specified at least with a
load limit of 12 times of the spotlights weight. Only safety
18
chain with approved connective can be used. Attach the
safety chain to its designated opening and attach it to the
truss system or a similar and safe attachment point. Assure to
close the fasteners as specified.
• To adjust the angle of the fixture open the locking screw, set
the fixure in its position and close it by hand.

Electrical Connection

• Connection to the mains is only allowed by skilled persons.
• Before connecting the fixture to the mains, assure that the
specifications are corresponding.
• Electrical grounding has to be used in the whole installation!
ATTENTION!
Installation has to be approved by an authorized person before
first operation!

Cleaning and Maintenance

• Installer has to take care of all safety and machinery installa­
tions are approved by skilled persons at least once a year.
• Installer has to take care of all safety and machinery installa­
tions are approved by authorized persons at least every four
years during the acceptance inspection. Following points need
to receive special attention:
• All screws used for mounting the fixture or parts of it need to
be proof and must not show corrosion.
• Housing, suspension device and installation site (ceiling, sus­
pension, truss) must not show deformation.
• All power cords must not show any damage, aging (for exam­
ple porous wires) or sediments. Other, to the location related
and usage aligned regulations will be observed by the skilled
person and safety defects will be fixed.
ATTENTION!
Make sure that the fixture is disconnected from mains during
all maintenance! It is important to unplug mains connector!
• The fixture must be regularly cleaned from dirt and dust. Only
use a wetted, lint­free cloth for cleaning the fixture. Never
use alcohol or any kind of solvent for cleaning.
• Inside the fixture there are no parts which need maintenance.
Maintenance & service must be done by authorized dealers
only.
• Only use original spare parts!
ADVICE!
If you have further questions, your local dealer will be happy to
help you.