Customer Service - Peg Perego Rocky Gebrauch Und Wartung

RULES FOR SAFE DRIVING
For the safety of the child, before starting up the toy
read and carefully follow the following instructions.
• Teach the child how to use the toy properly for
safe and enjoyable useful.
WARNING!
• Check that all the fixing studs/nuts are fastened
properly.
• If the toy is overloaded, the overload switch will
immediately disconnect the power. The power
supply will be restored after a few seconds.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE TOY DOES NOT WORK?
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE TOY LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

CUSTOMER SERVICE

offers an after-sales assistance service,
PEG PEREGO
directly or through a network of authorized
assistance centres, for any repairs or replacements
and the sale of original spare parts. To contact the
assistance centres refer to the "Assistance Centres"
booklet included in the packaging.
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and valuable
to us. We would be very grateful if, once you have
used the product, you would fill out the
which you can find on
SATISFACTION QUESTIONNAIRE
the internet at: www.pegperego.com, making
any observations or suggestions you might have.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE TOY
FROM ITS PACKAGING. ALL THE SCREWS AND
SMALL PARTS ARE CONTAINED IN A BAG INSIDE
THE PACKAGING. THE BATTERY MAY ALREADY
BE FITTED INSIDE THE ITEM.
1 • Remove the elastic holding strap from the
handles. Insert them into the 2 slots, ensuring
that the connection teeth are correctly attached
to the central pin and that the 2 buttons are
positioned as shown in the figure.
2 • Unfasten the 2 screws on the mane.
3 • Put the bridle on the horse's nose and over the
head as far as the handles, as shown in the figure.
Put the mane back in place and fasten the 2
screws.
4 • Roll up the upper end of the blanket and insert
the 2 ends in the matching loops, as shown in the
figure.
5 • Push the 3 plastic clips all the way down into
their holes in the saddle.
6 • Attach the saddle to the horse by pushing the 3
clips into the slots.
7 • Remove the holding band from the connectors in
the lower part of the horse. Insert 2 white
bushes into the matching holes on each side of
the horse.
8 • Push the 4 rubber feet into place underneath the
base.
9 • Hook up the connectors on the horse with
those on the base. WARNING: Match together
the connectors of the same colour.
10 • Take the shorter metal pin from the parts bag.
Slot it through the central area of the base and
the horse. WARNING: Ensure that the cables
connected in the previous step are protected
inside the horse and that the horse is facing the
right direction.
11 • Take the other pin from the parts bag and push
it through at the front, as shown in the figure.
12 • Put 2 self-locking washers in the 2 special tools
provided. Important: the tabs on the self-locking
washers must be pointing towards the inside of
the tools (see detail A).
13 • Put the 2 tools on the sides of the central pin
and push the 2 washers onto it.
14 • Use a hammer to ensure that they are securely
attached. Remove the tools.
15 • Put 2 more self-locking washers in the lower
part of the footrests, as shown in the figure.
WARNING: When turning over the footrests to
fit them, ensure that the washers do not fall out.
16 • Push the footrests on, ensuring that they are
facing the right way and that they go over the
ribs, as shown in the figure.
17 • Use a hammer to fix the footrests in place on
both sides, keeping the opposite side steady.
18 • Use a tool to turn the safety catch of the battery
compartment by 90° and remove the cover.
19 • Connect the electrical system plug to the battery
plug and put the cables back inside the
compartment. Close the battery compartment
again and secure it with the catch. The item is
ready for use.
FEATURES AND USE
20 • ON-OFF BUTTON: It deactivates (OFF – button
raised) and activates (ON – button pressed
down) the movement function.
21 • HANDLE CONTROLS: When the ON-OFF
button is ON, the black button on the right
starts the movement and a galloping sound, while
the red one on the left produces a neighing
sound.
When the ON-OFF button is OFF, the button on
the right produces the galloping sound, while the
one on the left produces the neighing sound.
In both the ON and the OFF mode, pressing the
red button on the left on its own produces 2
tunes.
• STOPPING: If the movement button on the right
handle is released, the item will stop
automatically.
REPLACING THE BATTERY
22 • Put the rear legs in the highest position and turn
the catch to open the battery compartment.
CONSUMER 23 • Disconnect the plugs by pressing them on the
sides.
24 • Remove and replace the battery. Reconnect the
plugs. Close the battery compartment again and
ASSEMBLY
secure it with the catch.
CHARGING THE BATTERY
WARNING: BATTERY CHARGING AND ANY
WORK ON THE ELECTRICAL SYSTEM MUST BE
CARRIED OUT BY AN ADULT.
THE BATTERY CAN BE CHARGED WITHOUT
REMOVING IT FROM THE TOY.
• Disconnect plug A of the electrical system from
the battery plug B by pressing the sides.
25 • Insert the battery charger plug in a domestic
power socket in accordance with the
instructions enclosed with it. Connect plug B to
the battery charger plug C.
• When charging is complete, detach the battery
charger from the domestic supply and then
disconnect plug C from plug B.
26 • Fully insert plug B into plug A, pushing until it
clicks. After completing the procedure, always
remember to close and secure the battery
compartment cover with the catch.