Extended Menu - Seav LRX 2214 SWR Handbuch

OFF).
The motor running time must be programmed when the shutter is down, in the follow-
ing manner:
Press the SEL button until the T. MOT LED flashes, then press and hold the SET but-
ton; the shutter will begin to move upwards. Once the desired position has been
reached, release the SET button; at this very moment, the motor running time will be
stored and the T. MOT LED will remain lit.
If you are using an automation which has a stop limit, we recommend that you set a
time which exceeds the stop limit of the shutter by a few seconds.
If you want unlimited motor time, perform the same programming procedure, holding
down the SET button for less than two seconds; the T. MOT LED will remain lit and the
unlimited time function will be set. The procedure may be repeated if a mistake is made
during programming.
WIND SPEED (Wind Safety threshold programming)
Displaying the programmed Wind threshold:
The Wind Safety threshold may be displayed in the following way: use the SEL button
to navigate to the WIND SPEED LED position; the LED will double-flash the same num-
ber of times as the stored Wind Safety threshold (each WIND SPEED LED double-flash
corresponds to an increase of 5 km/h), (for example: 5 WIND SPEED LED flashes = 25
km/h).
Wind Safety threshold selection from 5 to 40 km/h
The sensor is supplied with a default Wind Safety threshold setting of 25 km/h (WIND
SPEED LED OFF).
The Wind Safety threshold may be programmed in the following way: use the SEL but-
ton to navigate to the WIND SPEED LED, then press the SET button to start the pro-
gramming procedure: the WIND SPEED LED will double-flash at the same time (each
WIND SPEED LED double-flash corresponds to an increase of 5 km/h). Press the SET
button when the desired threshold has been reached; at that moment the selected
value will be stored in the memory and the WIND SPEED LED will remain lit (for exam-
ple: 5 WIND LED double-flashes = 25 km/h).
The procedure may be repeated if a mistake is made during programming.
SUN SENSOR (Sun sensor ON/OFF)
Enabling the Sun sensor:
The control unit comes with the Sun sensor disabled (SUN SENSOR LED OFF).
The Sun sensor may be enabled in the following way: press the SEL button until the
SUN SENSOR LED flashes, then press the SET button briefly; at this moment the SUN
SENSOR LED remains lit and the Sun sensor will be enabled. Repeat the procedure to
disable the Sun sensor.
Enabling the Sun sensor using a 3-button radio control (BeFree x3 - X6):
The Sun sensor may be enabled in the following way: press and hold the (+) button on
a previously stored radio control for 5 seconds; the control unit will cause the shutter
to move Up/Down for 1 second to confirm that the Sun sensor has been enabled, and
the SUN SENSOR LED will remain lit. Repeat the same procedure to disable the Sun
sensor, instead holding down the (-) button for 5 seconds.
RAIN SENSOR (Rain sensor ON/OFF)
Disabling the Rain sensor:
The control unit comes with the Rain sensor enabled (RAIN SENSOR LED ON).
The Rain sensor may be disabled in the following way: press the SEL button until the
RAIN SENSOR LED flashes, then press the SET button briefly; at this moment the RAIN
SENSOR LED switches off and the Rain sensor will be disabled. Repeat the procedure
to enable the Rain sensor.

EXTENDED MENU

The control unit is supplied by the manufacturer with the option of selecting only the
functions listed in the main menu.
To enable the extended menu functions proceed as follows: press and hold the SET
button for 5 seconds; the SUN and RAIN LEDs will start flashing alternately. the user
then has 30 seconds in which to select the extended menu functions using the SEL and
SET buttons. After 30 seconds the control unit returns to the main menu.
EXTENDED MENU
Reference LED LED Off
A) CODE remote PGM = OFF
B) SENS. CODE Wired sensor Test = OFF
C) T. MOT. Aut. movement lock = OFF
D) WIND SPEED Safety upward = OFF
E) SUN SENSOR SUN inversion = OFF
F) RAIN SENSOR RAIN inversion = OFF
G) SUN
H) RAIN
A) CODE
(Remote programming of radio control):
The control unit allows the transmission code to be programmed remotely, without
using the SEL button on the unit itself.
To programme a transmission code remotely, proceed as follows: send the radio con-
trol code continuously for more than 10 seconds; the control unit will enter the pro-
gramming mode as described above for the CODE LED in the main menu.
The control unit is supplied by the manufacturer with remote programming of a trans-
mission code not enabled; to enable the function proceed as follows: check that the
extended menu is enabled (SUN and RAIN LEDs flash alternately), use the SEL button
to navigate to CODE LED when flashing and press the SET button: the CODE LED
lights up and programming is complete. Repeat the procedure to restore the previous
configuration.
B) SENS. CODE (Wired sensor test):
The control unit can be used to check the operation of the connected sensors, and to
- 10 -
LED On
remote PGM = ON
Wired sensor Test = ON
Aut. movement lock = ON
Safety upward = ON
SUN inversion = ON
RAIN inversion = ON
Flashing beacon ON/OFF
Flashing beacon ON/OFF