Extended Menu - Seav BeSUN Series Bedienungsanleitung

the SET key for less than two seconds; the T.MOT LED will remain lit and the unlimited time
function will be set. The operation may be repeated if a mistake is made during programming.
3) LED WIND SPEED
Programmed wind threshold display
The wind safety threshold may be displayed in the following way: use the SEL key to navi-
gate to the WIND LED position; the LED will double-flash the same number of times as the
stored wind safety threshold (each WIND LED double-flash corresponds to an increase of 5
Km/h), (for example: 5 WIND LED flashes = 25 Km/h).
Wind safety threshold selection from 5 to 40 km/h
The control unit comes with a default wind safety threshold setting of 25 km/h (WIND
LED OFF).
The wind safety threshold may be programmed in the following way: use the SEL key to
navigate to WIND LED, then press the SET key to start the programming procedure: At the
same time the WIND LED will begin to double-flash (each double-flash of the WIND LED
corresponds to an increase of 5 km/h); press the SET key once the desired threshold has
been reached – at this moment, the selected value will be stored and the WIND LED will
remain lit (for example: 5 WIND LED double-flashes = 25 km/h).
The operation may be repeated if a mistake is made during programming.
4) LED MAN/AUT
Enabling the Sun Sensor
The control unit comes with the Sun Sensor disabled (MAN/AUT LED OFF).
The Sun Sensor may be enabled in the following way: press the SEL key until the MAN/
AUT LED flashes, then press the SET key briefly; at this moment the MAN/AUT LED remains
lit and the Sun Sensor will be enabled. Repeat the operation to disable the Sun Sensor.
Enabling the Sun Sensor using a 3-button radio control (BeFree x3 - X6):
The Sun Sensor may be enabled in the following way: hold down the (+) key on the radio
control that was programmed previously for 5 seconds; at the same time the control unit
will cause the shutter to move Up/Down for 1 second to confirm that the Sun Sensor has
been enabled, and the MAN/AUT LED will remain lit. Repeat the operation to disable
the Sun Sensor by following the same procedure, but instead holding down the (-) key
for 5 seconds.

EXTENDED MENU

The control unit is supplied by the manufacturer with the possibility of selecting only the
functions listed in the main menu.
To enable the functions of the extended menu proceed as follows: press the SET key and
hold for 5 seconds; the WIND and MAN/AUT LEDs will flash alternately and the user has
30 seconds within which to select the functions of the extended menu using the SEL and
SET keys. After another 30 seconds the control unit returns to the main menu.
————————————— EXTENDED MENU
Reference LED LED Off
A) CODE remote PGM = OFF
B) T. MOT. Aut. Movement lock = OFF
C) WIND
D) MAN/AUT
A) CODE (Remote programming of radio control):
The control unit allows the transmission code to be programmed by remote, without using
the SEL key.
To programme the transmission code from remote proceed as follows: send the radio
control code continuously for more than 10 seconds and the control unit will enter the
programming mode as described above for the CODE LED in the main menu.
The control unit is supplied by the manufacturer with remote programming of the trans-
mission code not enabled; to enable the function proceed as follows: check that the
extended menu is enabled (WIND and MAN/AUT LEDs start flashing alternately), use
the "SEL" key to navigate to the CODE LED when it is flashing and press the "SET" key:
the CODE LED lights up and programming is completed. Repeat the operation to restore
the previous configuration.
B) T. MOT. (Automatic movement lock):
The control unit enables the prevention of automatic movements (Up / Down sun blind
movements on the Sun Sensor command or the within the Automatic Downward move-
ment function), so that if a stop command is sent from a radio control during the move-
ment stage, the control unit locks the automatic movements until a new Up or Down
command is sent. The control unit is supplied by the manufacturer with the Automatic
Movement Lock disabled; to enable the function proceed as follows: check that the
extended menu is enabled (WIND and MAN/AUT LEDs start flashing alternately), use the
"SEL" key to navigate to the T.MOT LED and when it is flashing press the "SET" key: the
T.MOT LED will light up and programming is completed. Repeat the operation to restore
the previous configuration.
RESET:
To restore the default configuration, press the SEL and SET keys simultaneously; all indi-
cator LEDs will switch on and then off again immediately.
13
————————————
LED On
remote PGM = ON
Aut. Movement lock = ON
Flashing beacon ON/OFF
Flashing beacon ON/OFF
Rev. 3.0 03-07-2017