Seav LRX 2214 SWR Handbuch Seite 9

3) User present (Dip 1 OFF and Dip 2 ON)
The "User present" operating mode can be obtained using the radio control and the
keypad, i.e. control must be constantly enabled so that the blind or shutter can be
moved as necessary. The movement stops when the control is released.
4) Venetian blind operation (Dip 1 and 2 ON)
Venetian blind operation can be obtained using the radio control and the keypad; this
involves 2 seconds of User Present operation at the very start. It is possible, in this
manner, to rotate the slats of the Venetian blind in one direction or the other in order to
modulate the amount of light filtering through as desired. If the transmitted commands
last longer than 2 seconds, the blind will move upwards or downwards (depending on
the button pressed) until the motor running time has elapsed.
P B I
ROGRAMMING UTTONS AND NDICATOR
SEL button: selects the type of function to store in the memory; selection is indicated
by the LED flashing. The desired function can be selected by pressing the button
repeatedly. The selected function remains active for 15 seconds (flashing LED), after
which the control unit returns to its original status.
SET button: programmes the function that has been selected using the SEL. button.
Indicator LEDs
LED lit: option stored.
LED off: option not stored.
LED flashing: option selected.
MAIN MENU
Reference LED LED Off
1) CODE No code
2) SENS. CODE No code
3) T. MOT. Motor running time 2 minutes
4) WIND SPEED Wind safety 25 km/h
5) SUN SENSOR Sun sensor = OFF
6) RAIN SENSOR Rain sensor = OFF
7) SUN Sun Present = No
8) RAIN Rain Present = No
CODE ( Radio control programming )
Programming using a 1- or 2-button radio control:
To programme the transmission codes in the radio control, proceed as follows: press
the SEL button; the CODE LED begins to flash. Send the first preselected code using
the relevant radio control at the same time; when the CODE LED begins to flash rapid-
ly send the second code to be stored. The CODE LED will remain lit and the program-
ming will be complete. If the second code is not sent within 10 seconds, the control
unit exits the programming phase and selects operation using a single radio control
button.
Programming using a 3-button radio control in the "BeFree" series:
The control unit allows you to store the whole "BeFree" radio-control by programming
only the Up button.
L
EDS
LED On
TX Pgm code
Sensor code pgm.
Motor running time pgm.
Wind safety pgm.
Sun sensor = ON
Rain sensor = ON
Sun Present = Yes
Rain Present = Yes
To programme the "BeFree" radio control codes, follow this procedure: press the SEL
button; the CODE LED begins to flash. Press the Up button on the desired radio con-
trol at the same time; the CODE LED will remain lit and programming will be complete.
Deleting the codes: To delete all transmission codes stored in the memory, proceed
as follows: press the SEL button; the CODE LED will start to flash. Then press the SET
button; the CODE LED will switch off and the procedure is complete.
Radio control already stored warning:
If the user attempts to perform the programming procedure for a radio control which is
already stored in the memory, the CODE LED will begin to flash rapidly for a few
moments, to indicate that this procedure cannot be performed; the unit then returns to
the programming stage once again.
Maximum number of radio controls which can be stored:
If the maximum number of radio controls has been reached and a programming pro-
cess started, the control unit will indicate that it has failed by flashing all the LEDs
except the CODE LED, which will remain lit in a constant manner. After 10 seconds the
control unit exits programming mode.
SENS. CODE (Wireless sensor programming)
Wireless sensor programming (Sun – Wind – Rain):
To programme the Wireless sensor transmission code, proceed as follows: Use the SEL
button to navigate to a position where the SENS. CODE LED flashes; at the same time,
send the Wireless sensor code using the special button inside the sensor. The SENS.
CODE LED will remain lit in a fixed manner and programming will be complete. If the
Wireless sensor code is not sent within 2 minutes, the control unit exits programming
mode.
Deleting the codes:
To delete the Wireless Sensor codes stored in the memory, proceed as follows: press
the SEL button; the SENS. CODE LED will start to flash. Then press the SET button;
the SENS. CODE LED will switch off and the procedure is complete.
Wireless sensor already stored warning:
If the user attempts to perform the programming procedure for a Wireless sensor which
is already stored in the memory, the SENS. CODE LED will begin to flash rapidly for a
few moments, to indicate that this procedure cannot be performed; the unit then
returns to the programming stage once again.
Maximum number of Wireless sensors which can be stored:
If the maximum number of Wireless sensors has been reached and a programming
process started, the control unit will indicate that it has failed by flashing all the LEDs
except the SENS. CODE LED, which will remain lit in a constant manner. After 10 sec-
onds the control unit exits programming mode.
Warning indicator: If there is no communication between the Wireless sensor and the
control unit, after 20 minutes the safety upward movement will be activated automati-
cally. If this lack of communication persists, further commands will still, nevertheless,
result in the control unit being set to safety mode.
T. MOT. (Max. Motor Timer programming time 4 minutes)
The control unit comes with a motor power supply time of two minutes (T. MOT. LED
- 9 -