Extended Menu - Seav LRX 2215 Bedienungsanleitung

D) WIND SPEED (Wind Safety threshold programming)
Displaying the programmed Wind threshold:
The Wind Safety threshold may be displayed in the following way: use the SEL button
to navigate to the WIND SPEED LED position; the LED will double-flash the same num-
ber of times as the stored Wind Safety threshold (each WIND SPEED LED double-flash
corresponds to an increase of 5 km/h), (for example: 5 WIND SPEED LED flashes = 25
km/h).
Wind Safety threshold selection from 5 to 40 km/h
The sensor is supplied with a default Wind Safety threshold setting of 25 km/h (WIND
SPEED LED OFF).
The Wind Safety threshold may be programmed in the following way: use the SEL but-
ton to navigate to the WIND SPEED LED, then press the SET button to start the pro-
gramming procedure: the WIND SPEED LED will double-flash at the same time (each
WIND SPEED LED double-flash corresponds to an increase of 5 km/h). Press the SET
button when the desired threshold has been reached; at that moment the selected
value will be stored in the memory and the WIND SPEED LED will remain lit (for exam-
ple: 5 WIND LED double-flashes = 25 km/h).
The procedure may be repeated if a mistake is made during programming.

EXTENDED MENU 1

The control unit is supplied by the manufacturer with the option of selecting only the
functions listed in the main menu.
To enable the functions of extended menu 1, proceed as follows: press and hold the
SET button for 5 seconds; the T. MOT. and WIND SPEED LEDs will start flashing alter-
nately. The user then has 30 seconds in which to select the extended menu functions
using the SEL and SET buttons. After 30 seconds the control unit returns to the main
menu.
EXTENDED MENU 1
Reference LED LED Off
A) CODE remote PGM = OFF
B) SENS. CODE Safety upward mov. =OFF Safety upward mov. =ON
C) T. MOT. Flashing beacon ON/OFF
D) WIND SPEED Flashing beacon ON/OFF
A) CODE (Remote programming of radio control):
The control unit allows the transmission code to be programmed remotely, without
using the SEL button on the unit itself.
To programme a transmission code remotely, proceed as follows: send the radio con-
trol code continuously for more than 10 seconds; the control unit will enter the pro-
gramming mode as described above for the CODE LED in the main menu.
The control unit is supplied by the manufacturer with remote programming of a trans-
mission code not enabled; to enable the function proceed as follows: check that the
extended menu is enabled (T. MOT. and WIND SPEED LEDs start flashing alternately),
use the SEL button to navigate to the CODE LED when flashing and press the SET but-
LED On
remote PGM = ON
- 9 -
ton: the CODE LED remains lit in a constant manner and programming is complete.
Repeat the procedure to restore the previous configuration.
B) SENS. CODE (Safety upward movement):
The control unit is supplied by the manufacturer with the Safety upward movement
function disabled; if you wish to enable the function, so that after 12 hours of Wind sen-
sor inactivity the control unit automatically sends a command for Safety upward move-
ment, proceed as follows: check that the extended menu is enabled (T. MOT. and WIND
SPEED LEDs start flashing alternately), use the SEL button to navigate to the SENS.
CODE LED when flashing and press the SET button: the SENS. CODE LED remains lit
in a constant manner and programming is complete. Repeat the procedure to restore
the previous configuration.
EXTENDED MENU 2
The control unit is supplied by the manufacturer with the only option of selecting the
functions listed in the main menu directly.
To enable the functions in extended menu 2, proceed as follows: access extended
menu 1 (as described in the corresponding paragraph), then press the SET button
again and hold for 5 seconds; the T. MOT. and WIND SPEED LEDs will flash alternate-
ly and the user has 30 seconds within which to select the functions of extended menu
2 using the SEL and SET buttons. When this time has elapsed the control unit returns
to the main menu.
EXTENDED MENU 2
Reference LED LED Off
A) CODE Auto movements = OFF
B) SENS. CODE Anemometer Test = OFF
C) T. MOT. Flashing beacon ON/OFF
D) WIND SPEED Flashing beacon ON/OFF
A) CODE (Automatic Movement Lock):
The control unit enables the prevention of automatic movements (Up / Down sun blind
movements on the Wind sensor command or Automatic sensors function), so that if a
Stop command is sent from a radio control during movement, the control unit momen-
tarily locks the automatic movements until a new Up or Down command is sent.. The
control unit is supplied by the manufacturer with the Automatic Movement Lock dis-
abled; to enable the function proceed as follows: check that the extended menu is
enabled (T. MOT. and WIND SPEED LEDs start flashing simultaneously), use the SEL
button to navigate to the CODE LED when flashing and press the SET button: the
CODE LED remains lit in a constant manner and programming is complete. Repeat the
procedure to restore the previous configuration.
B) SENS. CODE (Wired Anemometer Test):
The control unit can be used to check the operation of the connected Wind sensor, and
to make sure the rotation direction is correct. When installing the device, we recom-
LED On
Auto movements = ON
Anemometer Test = ON