Sony CA-950 Bedienungsanleitung Seite 25

9 DC IN (direct current input) connector (4-pin)
Connects an AC adapter or battery case. Supplies
power to the CA-950/950P when the POWER switch
is set to EXT.
0 PROMPTER/GEN LOCK (prompter signal
input and output/external sync signal input)
connector (BNC type)
Inputs an external sync signal or inputs and outputs a
prompter video signal. Select the respective function
with the PROMPTER/GENLOCK switch on the
internal DPR board. The connector is factory set for
prompter video signal output.
When the BVP-9500WS/9500WSP is connected with
the CA-950/950P and the system is under super
motion (third times normal speed), this connector
cannot be used.
qa AUDIO IN 1/AUDIO IN 2 (audio input)
connectors (XLR type, 3-pin) and LINE/MIC
(line input/microphone) switch
Inputs external audio signals. Set the LINE/MIC
switch according to the input signal type.
The following power supply settings can be specified
for the external microphone:
OFF: No power is supplied to the external
microphone.
+48V: +48V is supplied to the external microphone.
q s TEST OUT (test video output) connector
(BNC type)
Outputs return video signals, playback video signals,
VBS signal, or monitor output signals. Normally
outputs monitor output signals when a CCU is
connected.
Note
Select the output signal with switch S1 on the IFF-633
board.
When BVP-9500WS/9500WSP is connected to the
system and it is under super-motion, the connector
does not output VBS signal and monitor output
signals, and outputs black and white return video
signal.
qd RET CONT (return control) connector (6-pin)
Inputs the control signal for selecting the return video
and for turning the intercom microphone on and off.
q f TRACKER connector (10-pin)
Use for communications with a tracker and intercom 1
and 2 communications. Also outputs the red and green
tally signals and program audio signals. The
maximum output current output from this connector is
1 A.
RS-232C input and output signals supports data
transmission and reception of 9600 bps with the CCU-
900/900P Camera Control Unit.
qg EARPHONE jack (mini-jack)
Connects an earphone for monitoring the audio from
the program.
qh CALL button
Use this button to call the CCU or MSU operator.
When this button is pressed, the red tally lamps on the
camera control unit (CCU) or master setup unit (MSU)
light up.
q j POWER switch
Selects the power supply.
1 CCU: Power is supplied from the CCU. The
indicator lights in green.
a (standby): Standby mode. The indicator lights in
red.
? EXT: Power is supplied from EXT DC IN
connector. The indicator lights in green.
The indicator blinks in red when the internal
temperature of this unit becomes abnormally high.
The indicator blinks slowly in green when the amount
of light that reached to the cable adapter through the
optical fiber cable is –17 to –20 dBm, and blinks fast
in green when the amount of light is less than –20
dBm.
qk SERIAL IN (serial digital video signal input)
connector (BNC type)
Inputs a component serial digital signal synchronized
with the camera system, and the signal is sent to the
AUX OUT connector of the CCU through the optical
fiber cable.
In the case of dual camera link system, connect this
connector with the SERIAL OUT connector of the
secondary CA-950/950P.
For setting of dual camera link, refer to the installation
manual supplied with the CCU-900/900P.
When using the camera as stand alone, leave this
connector unconnected. When the BVP-9500WS/
9500WSP is connected with the CA-950/950P and the
system is under super motion (third times normal
speed), this connector cannot be used.
7(E)