Sony CA-950 Bedienungsanleitung Seite 24

Location and Function of Parts and Controls
1 PGM 1 (program 1)/PGM 2 (program 2) switch
Switches program audio 1 and 2.
2 RET 1 (return video 1) button/RET (return
video) button and RET 2/3/4 switch
RET 1 (return video 1) button
Press this button to monitor the return video 1 signal
from the CCU in the viewfinder or on a monitor using
the TEST OUT signal .
RET (return video) button
Press this button to monitor the return video signal
from the CCU in the viewfinder. Select the monitored
signal with the RET 2/3/4 switch.
RET 2/3/4 switch
Selects the return video signal monitored in the
viewfinder while the RET button is pressed.
3 TALLY lamp and TALLY switch
When the TALLY switch is ON, the TALLY lamp
lights when a red tally signal or call signal is input
from the CCU.
Turning S1 on the IF-633 board to ON mixes and
outputs the battery alarm signal to the TALLY lamp.
4 PGM (program) level controls (for the CA-950)
Adjusts the audio volume of the program.
Note
PGM level controls are provided for both intercom 1
and 2.
5 INCOM (intercom) level controls, PROD/ENG
(producer/engineer) switches, and LEVEL/MIC
(intercom level/microphone) switches (for the
CA-950)
INCOM (intercom) level controls
Adjusts the audio volume of the intercom.
PROD/ENG (producer/engineer) switches
Switches the intercom line.
PROD: Selects the producer's line
ENG: Selects the engineer's line
LEVEL/MIC (intercom level/microphone) switches
The LEVEL and MIC switch settings specify the
following functions:
REAR/ON: Turns on the intercom microphone.
Adjust the intercom reception level with the
INCOM control.
6(E)
REAR/OFF: Turns off the intercom microphone.
Turn the intercom microphone on and off using
the control on the external equipment connected to
the RET CONT connector. Adjust the intercom
reception level with the INCOM control.
FRONT/OFF: Turns off the intercom microphone.
Turn the intercom microphone on and off using
the control on the external equipment connected to
the RET CONT connector. The intercom
reception level is adjusted with the control on the
camcorder.
Note
INCOM level controls and LEVEL/MIC switches and
PROD/ENG switches are provided for both intercom 1
and 2.
6 CCU connector
Connect a CCU-900/900P-series Camera Control Unit
through an optical fiber cable.
Note
A dual camera system or a stand-alone operation is not
activated when an optical fiber is connected to this
connector.
7 INCOM 1 (intercom 1)/INCOM 2 (intercom 2)
connectors
Connect a headset to enable the reception of program/
intercom audio and transmission of intercom audio.
Set the INCOM 1, INCOM 2 switches on the AU-237
board to "CM" when using a carbon-type headset, and
set it to "DYM" when using a dynamic-type headset.
The INCOM 1 connector can be used for
communications even though the power to the camera
is turned off on the CCU-900/900P.
8 REMOTE connector (8-pin)
Connects an RCP-700 Series or RM-B150 Remote
Control Unit for a stand-alone operation. Connection
must be made with a cable of 150 feet (50 meters) or
less in length.
When the CCU is connected, connect the remote cable
of the CA-905L.
Note
• Do not connect an RCP-700-series panel or an RM-
B150 when a CCU is connected.
• When connecting the RM-B150, use the cable
supplied with the RM-B150.