Mounting And Operation - Hitachi C 3606DA Bedienungsanleitung

English
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about
3 seconds to confi rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.

MOUNTING AND OPERATION

Action
Inclined cutting using the guide
(+45° direction)
Inclined cutting using the guide
(–5° direction)
Fine tuning of parallelism
Fine tuning of perpendicularity
Fine tuning of guide piece position
Adjusting the cutting depth
Cutting line
Switch operation
About the mode select function (*1)
Remaining battery indicator
Using the LED light
Attaching the long guide
(sold separately)
Attaching the guide
Attaching the dust collection adapter
(sold separately)
Attaching the fl uorine plate
(sold separately)
Removing and inserting the battery
Charging
Cutting at right angles
Inclined cutting (+45° direction)
Inclined cutting (–5° direction)
Dismounting the saw blade
Mounting the saw blade
Charging a USB device from a
electrical outlet
Charging a USB device and battery
from a electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
(*1) About the mode select function
Each time the mode selector switch is pushed, the
operation mode changes.
When Silent mode is selected, the Silent mode indicator
lamp lights up.
Silent mode reduces maximum motor RPM enabling
effi cient work with less noise.
If the load increases while the motor is operating in
Silent mode, it automatically changes to Power mode.
Additionally, if the load decreases again, it automatically
returns to Silent mode.
In Power mode, no change is made to Silent mode even
when the load decreases.
Figure Page
NOTE
○ The mode will only change after a battery is installed and
9 3
the switch is pulled once.
○ The current mode will be maintained even if the switch is
on/off , or the battery is removed/reinserted.
10 3
LED LIGHT WARNING SIGNALS
11 3
(Fig. 34)
12 3
13 3
This product features functions that are designed to protect
the tool itself as well as the battery. While the switch is
14 4
pulled, if any of the safeguard functions are triggered
15 4
during operation, the LED light will blink as described in
Table 3. When any of the safeguard functions are triggered,
16 4
immediately remove your fi nger from the switch and follow
the instructions described under corrective action.
17 4
18 4
19 4
20 5
21 5
22 5
23 5
24 5
25 5
26 6
27 6
28 6
29 7
30 7
16
Mode
Power
Silent
Fig. 34
31-a 8
31-b 8
32 8
33 8
― 312
No-load speed
4300 min
-1
2000 min
-1