Herunterladen Inhalt Inhalt Diese Seite drucken

Hydromassage Activation - Jacuzzi VIRTUS Montageanweisung

Vorschau ausblenden Andere Handbücher für VIRTUS:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 58
It is possible to vary the filtering cycle setting parameters at any
time by following the procedure provided at the beginning of this
chapter. By modifying these parameters, time "0" is "shifted"
to the time in which the new values are saved.
s
uspending tHe filtering cycles
 Activating the hydromassage stops the filtration cycle, but it
resumes about 5 minutes after the function has turned off.
Moreover, with these models, the "silence" mode also sus-
pends the filtering cycle (refer to the respective section for fur-
ther details).
 The filtering cycle may be suspended by the anti-freeze pro-
tection ("Smart Winter") or due to overheated water. Refer to the
respective chapters.
f
ilter and selector valve
The filter consists of a thermoplastic container, an internal distribu-
tion system and a selector valve.
The selector valve lever must be left in the "filtration" posi-
tion when using the hot tub.
The selector valve function must be changed with the filter
pump stopped, in order to avoid damage.
m
CAUTION: the pumps must be stationary before using
the selector valve.
The functions you can activate using the selector valve handle are:
"Winter" position: only needed when the hot tub is not used; it
helps to fully empty the water from the filter.
"Filtration" position: normal position during use. The pump
forces the water from the hot tub through the filtering materi-
al; the water is then collected in the lower filtering units in the
internal distribution system; finally, the water comes back up
through the return coupler and re-enters via the nozzles.
"Backwash" position: the pump drives the water into the filter
and is carried in the opposite direction to the filtering action,
so as to clean the filter itself. In this case, the water enters the
filter via the central pipe, leaves via the lower filtering units in
the internal distribution system, comes up through the filtering
material and exits via the coupler the drain pipe is connected to,
taking with it any deposits blocked by the filtration mass during
filtering.
"Rinse" position: in this position, the water is drained into the
drain pit after being filtered. The aim is to remove the first cycle
of filtered water and the position is used to clean the filtering
material (when the system is being started up, immediately after
having loaded the filtering material in the filter, or after it has been
changed).
c
p
3
learray
ro
tect
The Clearray Pro3tect™ system helps to disinfect and purify water,
thus reducing the need for chemical products.
 The Clearray Pro3tect™ system operates automatically and is
dependent on activation of the filtration pump during the filter-
ing cycle; it remains off when the hydromassage is on; Clearray
Pro3tect™ begins operating once again 40 minutes after switch-
ing off the aforementioned functions (where a filtering cycle is
active).

Hydromassage activation

This function is activated by pressing the "Pump"
(display B) or the
button (display A1/A2) (activation is also sig-
nalled by the respective LED - display B - which may also be flashing;
on displays A1/A2, the button briefly lights up blue, then returns to
white).
A1
 To activate the function:
- briefly press the "Pump"
1 on/off (the button briefly lights up blue, then returns to white);
- press the "Pump"
button (display A2) to turn pump 2 on/off
(the button briefly lights up blue, then returns to white);
- press the "Pump"
button once (display B) to turn on pump
1; press it again to turn on pump 2. Press the button a third
time to turn off pump 1 and a fourth time to turn off pump 2.
37
™ (
).
wHere expected
B
button (display A1) to turn pump
button
A2

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis