BH HIPOWER G930 Montage- Und Gebrauchsanleitung Seite 10

ASSEMBLY INSTRUCTIONS.-
Take the unit out of its box and make sure that all
of the pieces are there, Fig.1:
(69) Main post with handlebar and monitor; (H)
Electronic monitor; (1) Main body; (44) Rear central
post cover; (44) Front central post cover; (110-111)
Bottom trim covers, left and right (L & R) for the
knuckle joints on the focus bars; (38) Side trim
cover; (101) Knuckle joint spacers; (133) Screw M-
5x10; (112) Screw M-4x50; (102) Screw M-10x70;
(103) Self-locking nut M-10; (37) Screw M-5x6; (5)
Screw M-6x10; (8) Allen screw M-10x20; (14)
Grower spring washer M-10; (13) Flat washer M-10
Ø 18; (K) Combination spanners; (L) Star driver
spanner; (LL) Allen key; (143) The adapter. G-930
15v. 1Amp; (155) Bottle holder.
1.
ATTACHING THE MONITOR.-
Release screws (93), Fig.2, at the back of the
monitor.
Bring the monitor (H) to the handlebar stem (69)
Fig.2, connect the terminal (170) coming out of the
handlebar stem (69) and the monitor (H16), Fig.2.
Take hold of the Hand-grip connector (114),
sticking out of the main post 31, and plug it into
(H17), located at the back of the monitor (H), as
shown in Fig.2.
Insert the monitor (H) onto the handlebar stem
(69), as shown in Fig.2, making sure not to pinch
any of the cables. Next, slide the front of the
monitor onto the plate on top of the main post (69)
in the direction of the arrow, Fig.2, push the cables
down into the main post making sure not the pinch
any of the cables.
Replace the screws (93) removed previously.
2.
FITTING THE MAIN POST.-
Take hold of the post (69) and bring it up to the
boss on the main body (1), connect the terminals
(O), sticking out of the bottom of the post, with
terminal (P) coming up out of the top of the tube on
the main body (1), Fig.3, now slip the main post
over the boss on the main body in the direction of
the arrow, making sure not to snag any of the
cables.
Take screws (8), Spring washers (14) and flat
washers (13) and screw together as shown in
Fig.3A without tightening fully.
3
ATTACHING THE FOCUS BARS TO
THE FOOT BARS.-
Take the bottom section of the focus bar (98R) and
insert the spacer (101) into the knuckle joint at the
bottom end of the bar in the direction of the arrows
Fig.4A.
Having done this bring the focus bar to the foot bar
(154) and insert screw (102) along with washer
(13). Next, fit the washer (14) and screw on the
self-locking nut (103) securely.
Do the same for the left focus bar (98L) with the
foot bar (153).
When everything has been assembled, check that
the monitor works by doing some exercises. If it
works correctly then fully tighten the screws (8) on
the focus bars, Fig.3A. that were left hand tight in
step 2 of the assembly instructions.
4.
FITTING THE TRIM CAPS TO THE
KNUCKLE JOINTS.-
Take the two trim caps (110-111), marked on the
inside with the letter (R) and fit them onto focus bar
(98R), as shown in Fig.5A. Next use screw (133) to
screw the caps onto the focus bars and use screws
(112) to screw the caps together.
Do the same with the trim caps (L) for focus bar
(98L).
5
FITTING THE CENTRAL COVERS.-
.
Take the front (44) and rear (44) covers and
position them on the main post (69), Fig.6. Now
use the screws (141) to attach them to the post.
6.
FITTING THE SIDE TRIM COVER.-
Next, position the side cover (38) so that it faces
the bottom triangle on the main body and secure
the cover using screws (5).
Next, remove the screws from the main post (69),
Fig.7, position the bottle holder and secure it by
using the screws removed previously.
7.
LEVELLING.-
Once the unit has been placed into its final position
for doing exercise, make sure that it sits flat on the
floor and that it is level. This can be achieved by
screwing the adjustable support blocks (120) up or
down, as shown in Fig.8.
8.
MOVEMENT & STORAGE.-
The appliance is equipped with wheels (125)
making it easier to move about. The two wheels at
the front of the appliance make it easy to store the
machine away, as shown in Fig.9
9.
PULSE MEASUREMENT.-
Your pulse rate is measured by placing both hands
on pulse sensors (148) located on the seat
handgrips or the handlebar, see Fig.10.
NOTE:
You can also use the chest band (OPTIONAL
TELEMETRIC PULSE SENSOR) to measure your
heart rate.
The reading from the telemetric pulse rate takes
preference over the pulse sensors (148) located on
the seat handgrips or handlebar.
9
SK
LINE LINE LINE LINE
sportkoncept