Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
On the remote control:
3& FOLDER UP 5
- To the next MP3 folder
3* STOP
- End CD playback
<
3( SKIP +
- CD title skip forwards
4) PROG
- For the saving of CD programmes
4! Battery compartment (rear panel)
4@ MODE
- Activate the CD repeat function
4# SKIP —
- CD title skip backwards
- CD playback start/stop
4$ 4; PLAY/PAUSE
4% FOLDER DOWN 6 - To the previous MP3 folder
Inserting the batteries
The remote control requires a 3 V battery type CR2025, which
has been preinstalled at the factory. To protect against pre-
mature discharging we have isolated the poles with a plastic
strip, which you can simply pull out before initial operation. The
remote control is then ready for operation.
If the device no longer reacts reliably on the remote control
signal, the battery is depleted. Change the battery with a fresh
one of the same type.
>
For this open the battery compartment on the rear side of
the remote control 4!. To open press the battery holder's
locking device to the side and pull the holder out.
>
Before removing the old battery please take note of the bat-
tery's position by means of the inscription that is visible from
outside.
>
Remove the battery and replace it with a fresh one of the
same type. Thereby the inscription must still be visible from
the outside otherwise the device will not function and could
be damaged.
>
Slide the battery holder back into the remote control until
it locks into place.
Handling of batteries
A leaking battery can cause damage to the remote control.
>
If you do not intend to use the remote control for a long
time, remove the battery.
>
Do not attempt to recharge the battery.
Becoming acquainted with the remote control
Point the remote control towards the device when you activate
its buttons. The remote control functions at a distance of ap-
prox. 5m from the device and at an angle of at least 60°. For
transmission of the signal there must be no objects placed be-
tween the device and the remote control.
and random playback
Connecting the components
Loudspeakers
>
Connect the speaker wires of the right speaker to the right
speaker terminals:
• connect the red lead of the speaker wire to the
+ terminal
.
3%
• connect the black lead of the speaker wire to the
— terminal
.
3$
>
Connect the speaker wires of the left speaker to the
left speaker terminals:
• connect the red lead of the speaker wire to the
+ terminal
.
3@
• connect the black lead of the speaker wire to
the — terminal
.
3#
Power supply
>
Connect the power plug of the power cord
properly connected power socket 230 V ~ /50 Hz.
Switching the device on and off
>
To supply the device with mains power move the power
switch 3! on the rear panel of the micro system to the posi-
tion "I".
To switch the device on move the FUNCTION switch
>
the CD/MP3/USB or RADIO position. The micro system
is now operational and the green POWER indicator 2* as
well as the blue background illumination of the display y
light up.
>
To switch the device off move the FUNCTION switch
to the TAPE/
position.
>
To separate the appliance from mains power, remove the
plug from the mains power socket.
Selecting the programme source
You can select between the following programme sources:
• CD/MP3/USB - Playback of audio CDs, MP3-CDs or
- USB memory mediums
• TAPE
- Playback of audio cassettes
• RADIO
- Playback of radio stations
>
For this move the FUNCTION switch
position.
Setting the volume
>
To increase the volume, repeatedly press the VOL +
button or hold the button down until the device has reached
the desired volume.
>
To decrease the volume, repeatedly press the VOL —
ton or hold the button down until the device has reached
the desired volume.
Using headphones
You can connect headphones to the micro system with a
3.5mm jackplug (not supplied). The headphones socket 2) is
located on the front of the micro system behind the cassette
keys cover. When you have connected the headphones, the
- 34 -
3^ to a
2@ to
2@
2@ to the desired
2^
but-
2%
Werbung
Kapitel
Inhaltsverzeichnis
