Intended Use; Items Supplied; Technical Data; Safety Information - Silvercrest KH 2305 Bedienungsanleitung

Intended use

This micro system is intended exclusively for the playback
of audio CDs, MP3-CDs, CD-R, CD-RW, USB flash memory
mediums, audio cassettes and for the playback of radio pro-
grammes. Additionally, the micro system is suitable for the
recording of audio cassettes. The micro system is not intended
for use in commercial or industrial environments. No warranty
claims will be granted for damage resulting from improper use!

Items supplied

1 Micro-system
2 Loudspeakers
1 Remote control (incl. 3 V battery, CR-2025)
1 Operating instruction manual

Technical Data

Micro system
Rated voltage: 230 V ~ , 50 Hz
Power consumption:
In standby < 6 Watt
During operation 12 Watt
Frequency range radio: MW (AM): 526,5 -1606,5 kHz
VHF (FM): 87,5 – 108 MHz
Measurements (W x H x D)
Main device: 16 x 23,5 x 23,2 cm
Per box: 13 x 23,7 x 15 cm
Weight
Main device: approx. 2180 g
Per box: approx. 960 g
Speaker power rating.: 2 x 2 Watt RMS
Impedance: 4 Ohm
Max. output voltage
at the headphone socket: 250 - 260 mV
USB port
Readable memory
mediums: USB1.1 and 2.0 up to a
capacity of 2GB
CD Laser: Laser class 1
Operating temperature: 5° - 40°C
Storage temperature : —20° - 60°C
Protection class: II
Cassette player/recorder
Cassettes: Standard cassette
(C-90 or shorter)
Tape speed: 4.75 cm/sec.
Remote control
Battery: 1 x 3 V Type CR 2025

Safety information

• Do not permit children to handle electrical equipment with-
out supervision, as they cannot correctly assess the possible
dangers of injury.
• Unplug the power cord after every use and before cleaning,
so as to prevent the device from switching on inadvertently.
• Check the device and all parts for visible damages. The
safety concept can work only if the device is in a faultless
condition.
• The power plug must always be easily accessible, so that in
the event of an emergency the device can be quickly discon-
nected from the mains power supply.
Risk of explosion!
• Do not throw batteries into a fire.
• Do not recharge the batteries.
• Never open batteries, never solder or weld batteries. The
risk of explosions and injuries exists!
• Regularly check the condition of the batteries. Leaking
batteries can cause damage to the remote control or to the
device.
• If you do not intend to use the device for an extended pe-
riod, remove the batteries.
• If the batteries have leaked put on protective gloves and
clean the battery compartment and the battery contacts
with a dry cloth.
Risk of electrical shocks.
• Connect the device to an electrical wall socket with a mains
voltage of 230 V / 50 Hz.
• Do not operate the device if the connection cord or the
power plug is damaged.
• The connection cord or device should be immediately
repaired or exchanged by the customer service department
if they fail to function faultlessly.
• NEVER submerse the device in water. Wipe it only with a
slightly damp cloth.
• Do not expose the device to rain and never use it in a damp
or wet environment.
• Make sure that the power cord does not become wet during
operation.
• You must not open the device housing or repair the device.
Inside the device there is invisible laser radiation ("Laser
class 1"). Therefore in this case safety is not assured and the
warranty will become void.
• Do not place objects containing fluids, e.g. flower vases, on
or near the device.
• Notice regarding power disconnection
To completely disconnect the device from the power source
the power plug must be removed from the power socket.
For this reason the device should be placed in a position
where a constant unobstructed access to the power socket
is assured, thus in an emergency situation you are able to
immediately pull out the power plug. To eliminate the risk of
fire you should completely disconnect the power plug from
the power socket when the device is not going to be used
for a long time, for example, during holidays.
• Always grasp the power cord by the plug. Do not pull on
the cord itself and never touch the power cord with wet
hands as this could result in a short circuit or an electrical
shock. Do not place the device, furniture or anything else
on the power cord and make sure that it does not become
clamped. Never tie knots in the power cord and do not join
it to other cables. Place the power cord in a position where
it can not be trod on. A damaged power cord can cause a
fire or an electrical shock. Check the power cord from time
to time. Should it become damaged contact your nearest
authorized customer service centre or dealer to have it re-
placed.
- 32 -