Vitek VT-1515 SR Betriebsanweisung Seite 6

•
Make sure that the button (4) is not pressed (is in
released position "
•
Remove the lid (10) from the water tank (11), then
remove the water tank (11) itself and fill it with
cold water till the mark «MAX».
•
Cover the tank (11) with the lid (10) and place it on
the coffee maker body (3).
•
Insert the coffee filter (16) into the holder (15),
matching the ledge on the filter (16) with the slot
on the holder (15) and turn the filter (16) clock-
wise or counterclockwise (pic. 1, 2).
•
Add ground coffee into the filter (16) and attach
the filter holder (15) to the coffee maker boiler; to
do this, place the filter holder handle (13) under
the marking «INSERT» on the coffee maker body
(3), insert the holder (15) into the boiler and turn
the filter holder handle (13) in the direction of the
marking «LOCK» till bumping (pic. 3, 4)
•
Place a corresponding cup on the tray grid (2).
Note: The cups used need to be preheated, to do
this place the cups on the tray (9), during water heat-
ing in the boiler the tray heats up too, thus warming
the cups.
•
Insert the power plug into the mains socket.
•
Press the «ON/OFF» button (6) to switch the cof-
fee maker on, the indicator (7) will light up.
•
Wait till the indicator (5) lights up green, then set
the operating mode selection knob (8) to the po-
sition " " and watch as the cup is filled with pre-
pared coffee.
Note:
During the coffee maker operation the indicator (5)
will go out and light up again periodically, indicating
the heating element operation. This operation mode
keeps the boiler temperature within the set range.
•
After the cup is filled with coffee switch the water
supply off by setting the operating mode selec-
tion knob (8) to the position "".
•
After you remove the cup with the coffee, some
water may drip from the filter holder openings.
It is normal. Control the tray (1) filling, periodi-
cally pour out the liquid from it and wash the tray
(1) with water.
•
Switch the coffee maker off by pressing the «ON/
OFF» button (6), the indicator (7) will go out.
•
Wait till the coffee maker cools down and remove
the filter holder (15).
•
To remove the filter holder (15) turn the handle
(13) towards the marking «INSERT» on the coffee
maker body (3) and remove the holder.
•
Turning the filter (16) clockwise or counterclock-
wise, remove it from the holder (15), remove the
ground coffee remnants and wash the filter (16).
MAKING CAPPUCCINO
Attention! Be careful to avoid burns by hot steam.
VT-1515_IM.indd 5
").
Make coffee, as described in the chapter «MAKING
ESPRESSO», in the cup with enough capacity to add
frothed milk or cream.
•
Press the water/steam supply button (4) to switch
the steam supply mode «
indicator (5) lights up green, the coffee maker is
ready to make frothed milk.
Attention! When you switch the steam supply mode
on, some water may drip from the boiler. Be careful
to avoid burns by hot water drops.
•
Take a narrow high glass, preferably metal, and
fill it with cold milk or cream approximately by
1/3.
•
Put the tip of the cappuccinator pipe (12) into the
glass and set the operating mode selection knob
(8) to the position «
cinator pipe should not touch the bottom of the
glass, as this can prevent the steam release. With
certain skill you can make frothed milk in several
seconds.
Note: The first portion of steam may contain some
water; for dry water steam it is necessary to release
the steam into appropriate container during several
seconds.
•
Switch the steam supply off by setting the knob
(8) to the position "".
•
Switch the coffee maker off by pressing the «ON/
OFF» button (6), the indicator (7) will go out.
Important:
•
It is important that milk for making frothed milk
is fresh and without additives, i.e. so-called long
storage milk is not suitable for this purpose. Take
usual whole milk with fat content from 4 to 6%,
cream fat content should be not less than 10%.
•
Clean the cappuccinator pipe (12) and its tip
right after milk or cream frothing - to do this, put
the cappuccinator pipe with the tip into a glass
of water, switch the steam supply on by setting
the knob (8) to the position «
switch the steam supply off and switch the cof-
fee maker off.
•
Wait till the coffee maker cools down and detach
the cappuccinator pipe (12) tip, turning it clock-
wise, and wash it under running water.
WARMING THE DRINKS
You can warm up your drinks by putting the cappuc-
cinator pipe (12) into the cup with the drink.
•
Press the water/steam supply button (4) to
switch the steam supply mode «
till the indicator (5) lights up green.
•
Put the cappuccinator pipe (12) into the cup with
the drink you want to warm up.
•
Switch the steam supply on by setting the op-
erating mode selection knob (8) to the position
« ».
5
ENGLISH
» on and wait till the
». The tip of the cappuc-
», and after that
» on and wait
26.03.2013 10:59:52