Other Functions; Changing The Sound Settings; Adjusting The Sound Characteristics - Bal/Fad/Subw; Adjusting The Equalizer Curve - Eq3 - Sony CVM-BDM Bedienungsanleitung

Other functions

Changing the sound settings

Adjusting the sound
characteristics — BAL/FAD/SUBW
You can adjust the balance, fader, and subwoofer
volume.
1
Press (SEL) repeatedly until "BAL,"
"FAD" or "SUBW" appears.
The item changes as follows:
t MID* t HIGH*
LOW* 1 1
BAL (left-right) t FAD (front-rear) t
SUBW (subwoofer volume)*
*1 When EQ3 is activated (page 13).
*2 When the audio output is set to "SUBW-Out"
(page 13).
"-∞" is displayed at the lowest setting, and can
be adjusted up to 20 steps.
2
Press the volume +/– button
repeatedly to adjust the selected item.
After 3 seconds, the setting is complete and
the display returns to normal play/reception
mode.
Note
Adjust within 3 seconds of selecting the item.
With the card remote commander
In step 2, to adjust the selected item, press < or ,.
Adjusting the equalizer curve
— EQ3
You can adjust and store the equalizer settings
for different tone ranges.
1
Select a source, then press (EQ3)
repeatedly to select the EQ3 type.
2
Press (SEL) repeatedly until "LOW,"
"MID" or "HIGH" appears.
3
Press the volume +/– button
repeatedly to adjust the selected item.
The volume level is adjustable in 1 dB steps,
from –10 dB to +10 dB.
Repeat steps 2 and 3 to adjust the equalizer
curve.
To restore the factory-set equalizer curve,
press and hold (SEL) before the setting is
complete.
After 3 seconds, the setting is complete and
the display returns to normal play/reception
mode.
With the card remote commander
In step 3, to adjust the selected item, press < or ,.
Adjusting setup items — SET
1
2
3
4
t
1
2
Note
Displayed items will differ, depending on the source
and setting.
With the card remote commander
In step 3, to select the setting, press < or ,.
The following items can be set (follow the page
reference for details):
"
z
Clock Adjust (page 4)
CT (Clock Time)
To set "on" or "off" (
D.Info (Dual Information)
To display the clock and the display items at the
same time.
– "on": to display at the same time.
– "off" (
Beep
To set "on" (
AUX-A (AUX Audio)*
To turn the AUX source display "on" (
"off" (page 15).
SUBW/Rear*
To switch the audio output.
– "SUBW-Out" (
– "Rear-Out": to output to a power amplifier.
Dimmer
To change the brightness of the display.
– "Auto" (
– "on": to dim the display.
– "off": to deactivate the dimmer.
Contrast
To adjust the contrast of the display.
The contrast level is adjustable in 11 steps.
Demo*
To set "on" (
Press and hold (SEL).
The setup display appears.
Press (SEL) repeatedly until the
desired item appears.
Press the volume +/– button to select
the setting (example "on" or "off").
Press and hold (SEL).
The setup is complete and the display returns
to normal play/reception mode.
" indicates the default settings.
) (page 9, 10).
z
): to not display at the same time.
z
) or "off."
z
1
1
): to output to a subwoofer.
z
): to dim the display automatically
z
when you turn the lights on.
1 (Demonstration)
) or "off" (page 4).
z
continue to next page t
) or
z
13