Other Functions; Changing The Sound Settings; Adjusting The Sound Characteristics - Bal/Fad/Sub; Customizing The Equalizer Curve - Sony CDX-GT100 Bedienungsanleitung

Other functions

Changing the sound settings

Adjusting the sound
characteristics — BAL/FAD/SUB
You can adjust the balance, fader, and subwoofer
volume.
1
Press the select button repeatedly
until "BAL," "FAD" or "SUB" appears.
The item changes as follows:
LOW* t MID*
1
BAL (left-right) t FAD (front-rear) t
SUB (subwoofer volume)*
*1 When EQ3 is activated (page 8).
*2 When the audio output is set to "SUB" (page 8).
"ATT" is displayed at the lowest setting, and can
be adjusted up to 20 steps.
*3 When AUX source is activated (page 9).
2
Rotate the volume control dial to
adjust the selected item.
After 3 seconds, the setting is complete and
the display returns to normal play/reception
mode.

Customizing the equalizer curve

— EQ3

"CUSTOM" of EQ3 allows you to make your
own equalizer settings.
1
Select a source, then press (EQ3)
repeatedly to select "CUSTOM."
2
Press the select button repeatedly
until "LOW," "MID" or "HI" appears.
3
Rotate the volume control dial to
adjust the selected item.
The volume level is adjustable in 1 dB steps,
from –10 dB to +10 dB.
Repeat steps 2 and 3 to adjust the equalizer
curve.
To restore the factory-set equalizer curve,
press and hold the select button before the
setting is complete.
After 3 seconds, the setting is complete and
the display returns to normal play/reception
mode.
Tip
Other equalizer types are also adjustable.
8
t HI* t
1 1
2 t AUX* 3
Adjusting setup items — SET
1
Press and hold the select button.
The setup display appears.
2
Press the select button repeatedly
until the desired item appears.
3
Rotate the volume control dial to
select the setting (example "ON" or
"OFF").
4
Press and hold the select button.
The setup is complete and the display returns
to normal play/reception mode.
Note
Displayed items will differ, depending on the source
and setting.
The following items can be set (follow the page
reference for details):
" " indicates the default settings.
z
CLOCK-ADJ (Clock Adjust) (page 4)
CT (Clock Time)
To set "CT-ON" or "CT-OFF" (
BEEP
To set "BEEP-ON" ( ) or "BEEP-OFF."
z
AUX-A* 1 (AUX Audio)
To turn the AUX source display "AUX-A-ON"
( ) or "AUX-A-OFF" (page 9).
z
SUB/REAR* 1
To switch the audio output.
– "SUB-OUT" ( ): to output to a subwoofer.
z
– "REAR-OUT": to output to a power amplifier.
DIM (Dimmer)
To change the brightness of the display.
– "DIM-ON": to dim the display.
– "DIM-OFF" ( ): to deactivate the dimmer.
z
DEMO*
1 (Demonstration)
To set "DEMO-ON" (
z
LOCAL (Local seek mode)
– "LOCAL-ON": to only tune into stations with
stronger signals.
– "LOCAL-OFF" ( ): to tune normal reception.
z
MONO* 2 (Monaural mode)
To improve poor FM reception, select monaural
reception mode.
– "MONO-ON": to hear stereo broadcasts in
monaural.
– "MONO-OFF" ( ): to hear stereo broadcast in
z
stereo.
REG*
2 (Regional)
To set "REG-ON" ( ) or "REG-OFF" (page 7).
z
LPF* 3 (Low Pass Filter)
To select the subwoofer cut-off frequency: "LPF
OFF" ( ), "LPF125Hz" or "LPF 78Hz."
z
) (page 7).
z
) or "DEMO-OFF."