Fuel Filter - Stiga PARK PRO 20 4WD Gebrauchsanweisung

EN
Oil quantity:
Machine Oil volume, approx.
No filter
replacement
Prestige 1.9 litres
Pro25 2.0 litres
8. Start the engine and check for oil leaks.
9. Stop the engine. Wait a few minutes until all the
oil has run back into the crankcase.
10.Check the oil level in accordance with 4.2.
5.5.2 Oil filter
The oil filter must be replaced during every second
oil change, i.e. after 200 hours of operation. First
drain the engine oil and install the oil drainage plug
as described above. Then replace the oil filter as
follows:
1. Clean the area around the filter and dismantle
the filter.
2. Place the new filter with the hole facing up-
wards in a vessel.
3. Fill up with the new engine oil through the hole
in the filter until the level reaches the bottom of
the thread.
4. Wait 1-2 minutes so that the oil is absorbed by
the filter material.
5. Moisten the filter's gasket with oil.
6. Install the filter. First screw in the filter so that
the gasket comes into contact with the engine.
Then screw in the filter a further 2/3-1 turn.
7. Continue with point 7 in accordance with 5.5.1
Engine oil above.

5.6 Fuel filter

Pro 16 and Pro 20 (Briggs & Stratton)
Replace the fuel filter every season. See fig. 17:Z.
Prestige and Pro 25 (Kohler)
Replace the fuel filter after 1,500 hours of opera-
tion. See fig. 23:Z.
Check for fuel leaks once the new filter has been
installed.
5.7 Transmission, oil filter
The oil and the filter in the hydraulic power trans-
mission must be checked/adjusted or replaced at
intervals according to the table below.
Action
Check – adjusting level.
Changing oil.
Cleaning tank filter.
Replace filter in the hydrau-
lic circuit. Pro20, Pro25
Oil type: Synthetic oil 5W-50.
Oil volume at change: approx. 4.2 litres.
68
ENGLISH
5.7.1 Check – adjustment
1. Place the machine on a flat surface.
2. Read off the oil level in the reservoir. See fig.
Filter replace-
ment
3. If necessary, top up with more oil.
2.0 litres
2.1 litres
5.7.2 Draining
1. Operate the machine at varying speeds for 10-
2. Drive the machine up onto a block or similar so
3. Open the drive shafts' valves in accordance
4. Place one collection trough under the rear axle
5. Remove 2 drainage plugs from each axle. Use a
6. Remove the filler cap from the oil tank.
7. Only Pro20 and Pro25: Clean the area around
8. Allow all the oil to run out into the collection
9. Hand in the oil for disposal in accordance with
5.7.3 Cleaning tank filter
1. Press the filter casing (25:F)down into the up-
2. Pull up the filter casing together with filter and
3. Pull the filter (25:G) out of the casing.
4. Clean the filter with a suitable solvent and com-
5. Check that the rubber gasket (25:H) in the bot-
6. Reinstall the filter and spring in the casing. In-
1st time Then at
interval
7. Reinstall the unit in the tank. The upper part of
Hours of operation
- 50
5 200
5 200
19. The level should be level with the line.
20 minutes in order to warm up the transmission
oil.
that the right rear wheel is raised approximately
10 cm above the left rear wheel. See fig. 20.
Otherwise the machine should be on a level sur-
face. This measure allows the oil to run out of
the reservoir more easily.
with fig. 21.
and one under the front axle.
12 mm socket wrench. See fig. 22.
the hydraulic circuit's filter and dismantle the
filter. See fig. 18:A.
trough.
local provisions.
per section of the tank and move the casing for-
wards to the hole.
spring.
pressed air.
tom of the filter is intact.
sert the filter until it snaps into position in the
casing.
the filter casing must snap into position in the
slot in the upper section of the tank.