Additional Safety Rules - Makita 4101RH Betriebsanleitung

14. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
15. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust-related hazards.
Power tool use and care
16. Do not force the power tool. Use the correct
power tool for your application. The correct power
tool will do the job better and safer at the rate for
which it was designed.
17. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
18. Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
19. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
20. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
21. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
22. Use the power tool, accessories and tool bits
etc. in accordance with these instructions and in
the manner intended for the particular type of
power tool, taking into account the working con-
ditions and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Service
23. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
24. Follow instruction for lubricating and changing
accessories.
25. Keep handles dry, clean and free from oil and
grease.

ADDITIONAL SAFETY RULES

1. This tool is equipped with a portable residual
current device. Do not connect the tool to a
power supply without using the PRCD (Porta-
ble Residual Current Device). In case of dam-
age of the cord, it has to be replaced by the
manufacturer's service organization.
2. For additional protection against electric
shock, be sure to WEAR RUBBER GLOVES
AND RUBBER BOOTS during operation.
3. Check the wheel carefully for cracks or dam-
age before operation. Replace cracked or
damaged wheel immediately.
4. Use only flanges specified for this tool.
5. Be careful not to damage the spindle, flanges
(especially the installing surface) or bolt.
Damage to these parts could result in wheel
breakage.
6. When using the water feed, be careful not to
let water get into the motor. If water runs into
the motor, an electric shock hazard may
result.
7. Hold the tool firmly.
8. Keep hands away from rotating parts.
9. Make sure the wheel is not contacting the
workpiece before the switch is turned on.
10. Wait until the wheel attains full speed before
cutting.
11. Stop operation immediately if you notice any-
thing abnormal.
12. Do not attempt to lock the trigger in the "ON"
position.
13. Never attempt to cut with the tool held upside
down in a vise. This can lead to serious acci-
dents, because it is extremely dangerous.
(Fig. 1)
14. Before setting the tool down after completing
a cut, be sure that the wheel has come to a
complete stop.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing water pipe (Fig. 2)
First, unplug the tool. Loosen the wing bolt on the
depth guide and move the base down. Install the
water pipe on the blade case using the screw as
shown in Fig. 2. Attach the vinyl tube onto the water
pipe and attach the adapter on the vinyl tube to a fau-
cet of water mains pressure. Adjust the amount of
water flow by simply adjusting the water cock.
Installing or removing diamond wheel
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the wheel.
Hold the outer flange with the wrench and loosen the
hex socket head bolt in clockwise direction with the
hex wrench. Then remove the hex socket head bolt
and outer flange. (Fig. 3)
Install the diamond wheel, outer flange and hex
socket head bolt onto the spindle. Hold the outer
flange with the wrench and tighten the hex socket
head bolt in counterclockwise direction with the hex
wrench. BE SURE TO TIGHTEN THE HEX SOCKET
HEAD BOLT SECURELY. (Fig. 4)
CAUTION:
Use only the Makita wrench and hex wrench to install
or remove the wheel.
7