Specifications; Safety Instructions - Makita JN3200 Betriebsanleitung

English
1 Lock button
2 Switch trigger
3 Gauge for mild steel: 3.2 mm
4 Gauge for stainless: 2.5 mm
5 Mouth (3.5 mm clearance)
6 Wrench
7 Lock nut
8 Die holder

SPECIFICATIONS

Model
Max. cutting capacities
Steel up to 400 N/mm
Steel up to 600 N/mm
Steel up to 800 N/mm
Aluminum up to 200 N/mm
Min. cutting radius
Outside edge ............................................. 128 mm
Inside edge ................................................ 120 mm
Strokes per minute ........................................... 1,300
Overall length ............................................... 215 mm
Net weight ........................................................3.4 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed

Safety instructions.

SAFETY INSTRUCTIONS
Warning! When using electric tools, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury,
including the following. Read all these instruc-
tions before attempting to operate this product
and save these instructions.
For safe operation:
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Don't expose power tools to rain. Don't use
power tools in damp or wet locations. Keep work
area well lit. Don't use power tools in presence of
flammable liquids or gases.
4
Explanation of general view
9 Punch
10 Screw
11 Loosen
12 Cutting edge
13 Groove
14 Pin
15 Punch holder
16 Grind/sharpen: 0.3 – 0.4 mm
JN3200
2
................................3.2 mm
2
................................2.5 mm
2
................................1.0 mm
2
.........................2.5 mm
17 Remove dull portion
18 Die
19 Washer
20 Limit mark
21 Screwdriver
22 Brush holder cap
3. Guard against electric shock
Prevent body contact with grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
4. Keep children away
Do not let visitors contact tool or extension cord.
All visitors should be kept away from work area.
5. Store idle tools
When not in use, tools should be stored in dry,
high, or locked-up place, out of the reach of chil-
dren.
6. Don't force tool
It will do the job better and safer at the rate for
which it was intended.
7. Use right tool
Don't force small tools or attachments to do the
job of a heavy duty tool. Don't use tools for pur-
poses not intended; for example, don't use circu-
lar saw for cutting tree limbs or logs.
8. Dress properly
Do not wear loose clothing or jewelry. They can
be caught in moving parts. Rubber gloves and
non-skid footwear are recommended when work-
ing outdoors. Wear protective hair covering to
contain long hair.
9. Use safety glasses and hearing protection
Also use face or dust mask if cutting operation is
dusty.
10. Connect dust extraction equipment
If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used.
11. Don't abuse cord
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and
sharp edges.
12. Secure work
Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to oper-
ate tool.
13. Don't overreach
Keep proper footing and balance at all times.
14. Maintain tools with care
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating
and changing accessories. Inspect tool cords
periodically and, if damaged, have repaired by
authorized service facility. Inspect extension
cords periodically and replace if damaged. Keep
handles dry, clean and free from oil and grease.