Preparing The Mower For Long-Term Storage; Ordering Replacement Parts; Disposal And Recycling - EINHELL GH-PM 40 P Betriebsanleitung

Anleitung_GH_PM_40_P_SPK1__ 26.06.13 08:46 Seite 28
GB
7.2.5 Maintenance of the air filter (Fig. 23-24)
A soiled air filter will reduce the performance of the
engine because it will prevent enough air getting to
the carburetor. It is therefore imperative that regular
checks are made. The air filter should be checked
every 25 hours and cleaned if required. If the air is
very dusty the air filter should be checked more
regularly.
Important: Never clean the air filter with petrol or
inflammable cleaning agents. Clean the air filter with
compressed air or simply by knocking out any
soiling.
7.2.6 Maintenance of the spark plug
Check the spark plug for dirt and grime after 10
hours of operation and if necessary clean it with a
copper wire brush. Thereafter service the spark
plug after every 50 hours of operation.
Pull off the spark plug boot (Fig. 25) with a twist.
Remove the spark plug with the supplied spark
plug wrench.
Assemble in reverse order.
7.2.7 Repairs
After any repair or maintenance work, check that all
safety-related parts are in place and in proper
working order.
All parts which may cause injury must be kept where
they are inaccessible to children or others.
Important: In accordance with product liability
legislation we are not liable for any damages caused
by improper repairs or the use of spare parts that are
not original spare parts or parts approved by us. In
addition, we are also not liable for any damages
arising from improper repairs. Such work should be
performed by a customer services workshop or
authorized specialist. The same applies to accessory
parts.
7.2.8 Times of use
Lawn mowers are only permitted to be used on
workdays between the hours of 7.00 a.m. and 7.00
p.m. Please comply with statutory regulations, which
may vary from location to location.

7.3 Preparing the mower for long-term storage

Caution: Do not empty the petrol tank in enclosed
areas, near fire or when smoking. Petrol fumes can
cause explosions and fire.
1. Empty the petrol tank with a petrol suction pump.
2. Start the engine and let it run until any remaining
petrol has been used up.
3. Change the oil at the end of every season. To do
so, remove the used engine oil from a warm
engine and refill with fresh oil.
4. Remove the spark plug from the cylinder head.
Fill the cylinder with approx. 20 ml of oil from an
28
oil can. Slowly pull back the starter handle, which
will bathe the cylinder wall with oil. Screw the
spark plug back in.
5. Clean the cooling fins of the cylinder and the
housing.
6. Be sure to clean the entire machine to protect
the paint.
7. Store the machine in a well-ventilated place.
7.4 Preparing the mower for transportation
1. Empty the petrol tank (see item 7.3.1).
2. Always let the engine run until it has used up the
remainder of petrol in the tank.
3. Empty the engine oil from the warm engine.
4. Remove the spark plug boot from the spark plug.
5. Clean the cooling fins of the cylinder and the
housing.
6. Remove the start tension cable from the hook
(Fig. 1/Pos. 11). Slacken the wing nuts and fold
down the upper push bar.
7. Wedge a few layers of corrugated cardboard
between the upper and lower push bars and the
engine in order to prevent any chafing.

7.5 Ordering replacement parts

Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info

8. Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.