Technical Data; Before Starting The Equipment; Assembling The Components; Setting The Cutting Height - EINHELL GH-PM 40 P Betriebsanleitung

Anleitung_GH_PM_40_P_SPK1__ 26.06.13 08:46 Seite 23
Bitte beachten Sie, dass unsere Geräte
bestimmungsgemäß nicht für den gewerblichen,
handwerklichen oder industriellen Einsatz konstruiert
wurden. Wir übernehmen keine Gewährleistung,
wenn das Gerät in Gewerbe-, Handwerks- oder
Industriebetrieben sowie bei gleichzusetzenden
Tätigkeiten eingesetzt wird.
The operating instructions as supplied by the
manufacturer must be kept and referred to in order to
ensure that the lawn mower is properly used and
maintained. The instructions contain valuable
information on operating, maintenance and servicing
conditions.
Important! Due to the high risk of bodily injury to the
user, the lawn mower may not be used to trim
bushes, hedges or shrubs, to cut scaling vegetation,
planted roofs, or balcony-grown grass, to clean (suck
up) dirt and debris off walkways, or to chop up tree or
hedge clippings. Moreover, the lawn mower may not
be used as a power cultivator to level out high areas
such as molehills.
For safety reasons, the lawn mower may not be used
as a drive unit for other work tools or toolkits of any
kind.

4. Technical data

Engine type:
Single cylinder four-stroke engine, 118 ccm
Engine power:
Working speed:
Fuel:
Tank capacity:
Engine oil:
Spark plug:
Electrode spacing:
Cutting height adjustment: dezentral, (32/46/62 mm)
Cutting width:
L sound pressure level:
pA
K uncertainty
pA
L sound power level:
WA
Vibration a
hw
K uncertainty
Weight:

5. Before starting the equipment

5.1 Assembling the components

Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the
instructions below.
Important! You will need the following additional
tools (not supplied) for assembly, and also for
maintenance work:
An open-ended wrench (10 mm)
A ring wrench (17 mm)
A ratchet, extension, size 13 socket
An open-ended wrench (13 mm)
A flat oil drip tray (for changing the oil)
A 1 liter measuring jug (oil/petrol resistant)
A petrol can (5 liters is sufficient for approx. 6
operating hours)
A funnel (suitable for the tankʼs petrol filler neck)
Household wipes (to wipe up oil/petrol residue;
dispose of these at a filling station)
A petrol suction pump (plastic, available from DIY
stores)
An oil can with hand pump (available from DIY
stores)
1 liter of engine oil (15W-40)
Assembling the lawn mower
1. Take the mower and attachment parts out of the
packaging and check that all parts are present
(Fig. 2-3).
2. Fasten the lower push bar to the mounts on the
mower housing (Fig. 4-5).
3. Now screw the upper push bar to the lower push
bar (Fig. 6-8). Pull the cords over the star nut so
1.6 kW/2,2 HP
that they do not get kinked when the push bar is
2800 min -1
swung down (Fig. 7) and make sure that the
standard petrol
starter cord guide (Fig. 8/Item 20) on the right
faces inwards.
approx. 1.3 l
4. Then hook the starter cord in the starter cord
approx. 0.4 l / 15W40
guide (Fig. 9)
FG RTC
5. Fasten the cord holder to the lower push bar
(Fig. 10).
0.6 mm
6. Secure the cords to the upper push bar with the
supplied cable tie (Fig. 11)
400 mm
7. Hook the grass basket into the mounts on the
mower (Fig. 15).
75 dB(A)
3 dB

5.2 Setting the cutting height

96 dB(A)
Important! Adjust the cutting height only when
5.73 m/s 2
the engine is switched off and the plug boot has
1.5 m/s 2
been pulled.
24 kg
Before you begin to mow, check to ensure that
the blade is not blunt and that none of the
fasteners are damaged. To prevent any
GB
23