Operation - Vitek VT-1689 SR Betriebsanweisung

ENGLISH
Materials and cookware not suitable for microwave ovens
Aluminium trays and foil
Cardboard cup with metal
handle
Metal cookware or
cookware with metal rim
Metal twist-ties
Paper bags
Soap
Wood
ASSEMBLING OF ThE MICROWAVE OVEN
After unit transportation or storage at low tempera-
ture it is necessary to keep it for at least two hours
at room temperature before switching on.
–
Remove the package and the accessories from the
oven cavity.
–
Check the microwave oven for damages. Pay spe-
cial attention to the condition of the door. If there
is any problem, do not set and do not switch the
oven on.
–
Place the microwave oven unrestricted. Provide air
access to the oven for ventilation at all sides. En-
sure at least 30 cm free space above the oven, the
gap to the rear and sides of the oven should be at
least 7-8 cm.
Protective covering
Body: if there is a protective film on the unit body, re-
move it from its surface.
Do not remove a light-gray mica plate inside the
cavity at the microwave output point (6), as it
serves for magnetron protection.
Installing the glass rotary bottom plate
•
Set the roller support (5) in the opening on the oven
cavity bottom .
•
Set the roller ring (4) on the oven cavity bottom.
•
Carefully set the glass rotary bottom plate (3) on the
roller ring (4), matching its ledges with the grooves
on the support (5).
•
Never set the glass rotary bottom plate with its bot-
tom side up.
•
Do not prevent rotation of the glass rotary bottom
plate while oven operation.
•
Always use the glass bottom plate (3), roller support
(5) and the roller ring (4) when cooking.
•
Cookware should be always set only on the glass ro-
tary bottom plate (3).
•
Glass rotary bottom plate (3) can rotate clockwise
or counterclockwise.
•
If cracks or chops appear on the glass rotary bot-
tom plate (3), stop using the unit immediately and
replace the bottom plate.

OPERATION

Before switching the oven on, make sure that the mains
voltage corresponds to the voltage specified on the
unit body.
VT-1689_IM_Bel.indd 6
May cause sparking. Use the cookware specially intended for microwave oven.
May cause sparking. Use the cookware specially intended for microwave oven.
Microwaves can not go through metal. Metal rim may cause sparking.
May cause sparking and burning of the package during cooking/heating products.
May cause burning in the microwave oven.
Soap may melt and make the oven cavity dirty.
Wooden cookware may dry out, crack and burn.
Notes:
–
–
Current time setting
When the microwave oven is connected to the mains,
you will hear a sound signal, the display lighting will light
up, and all operating modes icons will appear.
1. Press the «Clock/Timer» button (15), the flashing
2. Turn the knob (17) to set «hours».
3. Press the «Clock/Timer» button (15), the flashing
4. Turn the knob (17) to set «minutes».
5. Press the «Clock/Timer» button (15) to finish time
6. In cooking mode (microwaves, grill, combi) press the
Notes:
–
–
–
Cooking in the microwave oven
Select the power level of the microwave oven and set the
cooking time to cook.
1. Open the door, put a bowl with products into the
2. Press the «Microwaves» button (11), you will hear
Note: To select the necessary power level press the
«Microwaves» button (11) or turn the knob (17). The mi-
crowave power modes will be shown on the display (10).
6
Every pressing of the control panel buttons (11-16,
18) or turning of the knob (17) is accompanied by a
sound signal.
The display lighting goes out approximately in 5
minutes after the last operation.
figures (20) «00:» will appear on the display (10) and
the icon (26) will light up. You can set the time in the
range from 0:00 to 23:59.
figures (20) «:00» will appear on the display (10).
setting. The set time will be shown on the display (10)
and the divisional symbol «:» will be flashing.
«Clock/Timer» button (15), and the current time will
be shown on the display during 2-3 seconds.
If the time value is not set, the current time will not
be shown on the display (10).
If the set time is not confirmed within 1 minute, the
display (10) will show the original indication.
If you have incorrectly inputted current time, press
the «Stop/Cancel» button (16) to reset the value
and repeat the current time setting points 1 to 5.
oven cavity and close the door.
a sound signal, the symbol «Р-100» will be flash-
ing on the display (10) and the icons (21) and (22)
will light up.
21.06.2013 11:19:15