Maintenance; Disposal And Recycling - Scheppach HL3000GM Original Bedienungsanleitung

15. Maintenance

Attention!
Pull out the power plug before carrying out any main-
tenance work on the equipment. Make sure that the
drive shaft is not connected to the traction unit.
When must the oil be changed?
First oil change after 50 operating hours, then every
250 operating hours.
Oil change (Fig. 18)
Position the kindling splitter on a slightly raised sur-
face (e.g. euro pallet). Place a sufficiently large con-
tainer (at least 30 litres) under the drain plug on the
splitting column. Open the drain plug and carefully let
the oil run into the container.
Open the filling screw on the top of the split-
ting column so the oil can drain more easily. Re-
place the drain plug and its seal and tighten it.
Pour in fresh hydraulic oil (Contents: see Technical
data) and check the oil level with the dipstick. After
changing the oil, operate the kindling splitter a few
times without actually splitting.
Warning! Ensure that no debris gets into the oil
container.
Dispose of the used oil in a correct manner at a
public collection facility. It is prohibited to drop
old oil on the ground or to mix it with waste.
We recommend oil from the HLP 32 range.
Changing the transmission oil, Fig. 20
The transmission has been filled with SAE90 trans-
mission oil by the factory. After the first 50 operating
hours, drain the transmission oil and replace it as de-
scribed with new oil. The next oil changes will then
need to be carried out every 250 operating hours or
every six months, depending on which happens first.
1. Disassemble the drive shaft protective cap and
place a sufficiently large container under the
transmission.
2. First open the oil drain plug (19), then the oil filler
opening (17) and completely drain the oil.
3. Close the oil drain plug with a new seal and, using
a funnel, pour in new SAE90 transmission oil into
the filler opening until the lower edge of the sight
glass (18) is almost covered in oil.
Check the oil level every 8 hours. The oil level is cor-
rect when the lower edge of the display (18) is almost
covered in oil.
Hydraulic system
The hydraulic unit is a closed system with oil tank, oil
pump and control valve.
28 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
The system is complete when the machine is deliv-
ered, and may not be changed or manipulated.
Connections and repairs
Connections and repairs of electrical equipment may
only be carried out by an electrician.
ATTENTION ! Observe the correct direction of rota-
tion when inserting the saw blade.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Machine data - type plate
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: splitting wedge guides, hydraulic oil,
splitting wedge, Transmission oil
* Not necessarily included in the scope of delivery!

16. Disposal and recycling

The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic.
Defective components must be disposed of as spe-
cial waste. Ask your dealer or your local council.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must
not be disposed of together with domestic
waste in compliance with the Directive
(2012/19/EU) pertaining to waste electrical and elec-
tronic equipment (WEEE). This product must be dis-
posed of at a designated collection point. This can
occur, for example, by handing it in at an authorised
collecting point for the recycling of waste electrical
and electronic equipment. Improper handling of
waste equipment may have negative consequences
for the environment and human health due to poten-
tially hazardous substances that are often contained
in electrical and electronic equipment. By properly
disposing of this product, you are also contributing
to the effective use of natural resources. You can
obtain information on collection points for waste
equipment from your municipal administration, pub-
lic waste disposal authority, an authorised body for
the disposal of waste electrical and electronic equip-
ment or your waste disposal company.