Troubleshooting; Disposal; Technical Data - CMi C-ERM-1200/32 Originalbetriebsanleitung

Rasenmaeher_Elektro_302150_115215.book Seite 33 Freitag, 23. Oktober 2015 8:46 08

Troubleshooting

What to do when something doesn't
work...
DANGER! Risk of injury! Unprofes-
sional repairs may mean that your
unit will no longer operate safely.
This endangers you and your envi-
ronment.
Error/Fault
Unit does not switch on.
Motor does not continue to
run.
Strange noise.
Cut result is not sufficient.
If you can't fix the fault yourself, contact your
nearest vendor. Please be aware that any
improper repairs will also invalidate the war-
ranty and additional costs may be incurred.

Disposal

Disposal of the appliance
Appliances which are labelled with
the adjacent symbol must not be dis-
posed of in household waste. You
must dispose of such old electrical
and electronic equipment separately.
– Please check with your local authority
about the possibilities for correct dis-
posal.
Through separate disposal you send old
equipment for recycling or for other forms of
re-use. You will thus help to avoid in
some cases that damaging material gets into
the environment.
Disposal of the packaging
The packaging consists of card-
board and correspondingly marked
plastics that can be recycled.
– Make these materials available
for recycling.

Technical data

Part number 302 150, 115 215
Nominal voltage 230–240 V~, 50 Hz
Malfunctions are often caused by minor
faults. You can easily remedy most of these
yourself. Please consult the following table
before contacting the vendor. You will save
yourself a lot of trouble and possibly money
too.
Cause
Did you wait for the delay?
Has the safety switch triggered
due to an overload or over-
heating?
Screws/parts come loose?
Foreign objects in the blades? Remove foreign objects.
Blade damaged?
Blade is blunt?
Part number
Nominal output
• 302 150
• 115 215
Protection class
Protection rating
Working width
Cutting height
Capacity of collection
box
Weight
Noise power level
(L )*
WA
Noise pressure level
(L )*
PA
Vibration**
*) The specified values are emission values and do not necessar-
ily represent safe workplace values. Although there is a corre-
lation between emission and immission levels, this cannot be
used to infer whether additional safety measures are necessary
or not. Factors which affect the current immission levels at the
workplace, include the type of room, other sources of noise,
e. g. the number of machines operating and other processes
taking place in the vicinity. Permitted workplace values can dif-
fer from country to country. This information is designed to help
the user to better assess the dangers and risks.
**) The specified vibration emission value was measured in
accordance with a normed test procedure and can be used in
order to compare one tool with another. The specified vibration
emission value can also be used for an introductory evaluation
of the exposure. The vibration emission value may fluctuate
from the specified value during actual use of the power tool.
These fluctuations will depend on the way in which the power
tool is used. Try to keep vibrations to a minimum. One method
of reducing the vibration load is, for example, limiting the length
GB
Remedy
Wait for the switch on delay
of 2 seconds.
De-energise the product and
wait for a few minutes until the
safety device has reset.
Tighten screws.
Have blade sharpened, or re-
place.
302 150, 115 215
1000 W
1200 W
II
IPX4
320 mm
27 / 45 / 62 mm
30 l
9,4 kg
96 dB(A)
68,1 dB(A)
(K = 3 dB(A))
2,5 m/s²
(K = 1,5 m/s²)
33