Installation - auna multimedia 10029401 Bedienungsanleitung

POWER SOURCE
Power Source
POWER SOURCE
Insert the small plug from the supplied
Insert the small plug from the supplied AC/DC adapter
AC/DC adapter to the DC in jack on
Insert the small plug from the supplied
to the DC in jack on the unit . Insert the AC/DC adapter
the unit. Insert the AC/DC adapter to
AC/DC adapter to the DC in jack on
to DC in jack on the unit .
DC in jack on the unit.
the unit. Insert the AC/DC adapter to
DC in jack on the unit.
BATTERIES INSTALLATION (REMOTE CONTROL)
Batteries Installation (Remote Control)
BATTERIES INSTALLATION (REMOTE CONTROL)
To replace the button cell:
1. Push the tab, then slide out the
1 . Push the tab, then slide out the battery tray as the To replace the button cell:
figure on the right.
battery tray as the figure on the right.
1. Push the tab, then slide out the
2 . Replace the old button cell by a new CR 2025 button 2. Replace the old button cell by a new
battery tray as the figure on the right.
cell as the polarity markings on the remote control.
CR 2025 button cell as the polarity
2. Replace the old button cell by a new
3 . Close the battery tray.
markings on the remote control.
CR 2025 button cell as the polarity
3. Close the battery tray.
markings on the remote control.
3. Close the battery tray.
BATTERY PRECAUTIONS:
Battery Precautions
BATTERY PRECAUTIONS:
Follow these the size and type of battery specified.
1 . Use only the size and type of battery specified.
1. Use only the size and type of battery specified.
Follow these the size and type of battery specified.
2 . Be sure the follow the correct polarity when installing the battery as indicated in the battery com-
2. Be sure the follow the correct polarity when installing the battery as indicated
1. Use only the size and type of battery specified.
partment. A reversed battery may cause damage to the device.
in the battery compartment. A reversed battery may cause damage to the
2. Be sure the follow the correct polarity when installing the battery as indicated
3 . If the battery in the device is consumed or the device is not to be used for a long period of time,
device.
in the battery compartment. A reversed battery may cause damage to the
remove the batteries to prevent damage or injury from possible battery leakage.
3. If the battery in the device is consumed or the device is not to be used for a long
device.
period of time, remove the batteries to prevent damage or injury from possible
4 . Do not try to recharge the battery not intended to be recharged; it can overheat and rupture.
3. If the battery in the device is consumed or the device is not to be used for a long
battery leakage.
period of time, remove the batteries to prevent damage or injury from possible
5 . The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
4. Do not try to recharge the battery not intended to be recharged; it can overheat
battery leakage.
6 . Clean the battery contacts and also those of the device prior the battery installation.
and rupture.
4. Do not try to recharge the battery not intended to be recharged; it can overheat
7 . Do not mix different types of batteries together (e.g. Alkaline and Carbonzine) or old batteries with
5. The batteries shall not be exposed to excessive heat such as sunshine, fire or the
and rupture.
fresh ones .
like.
5. The batteries shall not be exposed to excessive heat such as sunshine, fire or the
6. Clean the battery contacts and also those of the device prior the battery
like.

installation.

6. Clean the battery contacts and also those of the device prior the battery
7. Do not mix different types of batteries together (e.g. Alkaline and Carbon-
installation.
zine) or old batteries with fresh ones.
7. Do not mix different types of batteries together (e.g. Alkaline and Carbon-
zine) or old batteries with fresh ones.
Installation
5
5
OPEN
OPEN
PUSH
PUSH
17